Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
Search Results "Horizontal Exit"
-
11B-404.2.10 Door and gate surfaces
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
-
5.4.2.2 Transfer and Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces
Rational for the recommendation A transfer support (for transfer surfaces less than or equal to 24” deep) is to extend horizontally along the side of the patient scanning/imaging table...
-
4. Wheelchair seat depth
Wheelchair seat depth For this study, wheelchair seat depth was calculated as the horizontal distance from the proximal (i.e., towards the rear) edge to the distal (i.e., towards the...
-
2.2 Lighting Conditions
On each trial one measurement of horizontal illuminance was manually recorded from a Minolta T-1 Illuminance meter....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
11B-703.8.4 Character height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
5.4.4 Transfer Support Distance from Transfer Surface Recommendations for M301 and M302
The gripping surface measurement is horizontal from the adjacent edge of the transfer surface (see figure 5.4.1). NPRM Proposed Provision: M305.2.1 Location....
-
11B-703.8.4 Character height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
11B-703.8.4 Character height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
Standing Supports (M304.3 and M305.3)
M305.3 also provides technical criteria for standing supports in horizontal and vertical positions....
-
Takeform Fusion Signage Interior Stairwell Type N
Fire and building code typically requires that stairwells in buildings of three floors or more identify the floor and exit point. Raised text and Braille are not required....
-
1. Standing Supports
the other to provide a standing support on only one side of the standing surface, provided that the standing support complies with the requirements in M305.3 for standing supports in a horizontal...
-
4.29.3* TACTILE WARNINGS ON DOORS TO HAZARDOUS AREAS
Such textured surfaces shall not be provided for emergency exit doors or any doors other than those to hazardous areas....
-
1132A.5.2 Strike edge maneuvering space at doors
The width of the level area at the exterior side of the primary entry door and any required exit doors shall comply with Section 1126A. Notes: 1....
-
Takeform Fusion Signage Evacuation Map Type D
Locations: Elevator Stairwell exits Hotel rooms Classrooms Type D 9.5"w x 17.75"h Insert Size: 8.5"w x 14"h...
-
Gaps
coordinated with the floors of the load and unload areas so that when the ride is at the load and unload position, the vertical differences between the two floors are within 5/8 inch and the horizontal...
-
R409.6 Gripping Surface
Where provided, horizontal projections shall occur 38 mm (1.5 in) minimum below the bottom of the handrail gripping surface. Advisory R409.6 Gripping Surface....
-
11B-806.2.3.1 Personal lift device floor space
The clear space shall extend to points horizontally 30 inches (762 mm), vertically 7 inches (178 mm) and not more than 12 inches (305 mm) from the head and foot end of the bed....
-
Is there a minimum distance between changes in level?
The standards do not require a minimum horizontal separation between changes in level of a ½” or less....
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Pole-supported pedestrian traffic control buttons shall be identified with color coding consisting of a textured horizontal yellow band 2 inches (51 mm) in width encircling the pole, and...
