The NORTON 5600 Series Hands-Free Kits combine a wave-to-open switch with the 5600 power operator to open the door and provide a ‘clean’ exit without touching hardware....
Search Results "Horizontal Exit"
Commonly Searched Documents
- Norton Surface Mounted Series 5600 Hands-Free Door Operation Kits
 - Landscape Forms Inc. Scarborough Bench Collection
 - 
    
  
  Sloped Surfaces
  
The amount of slope or grade is described as the proportion of a vertical rise to a horizontal length....
 - 
    
  
  Running Slope [1017.7.1]
  
Running slope is often described as a ratio of vertical distance to horizontal distance, or rise to run (figure 9)....
 - 
    
  
  810.5.3 Platform and Vehicle Floor Coordination
  
light rail, commuter rail, and intercity rail systems subject to Department of Transportation regulation 49 CFR 37.21 where it is not operationally or structurally feasible to meet the horizontal...
 - 
    
  
  Elevator Doors
  
The proposed rule recognized horizontal sliding doors....
 - 
    
  
  405.9 Edge Protection
  
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (13 mm) maximum within 10 inches (255 mm) horizontally of the minimum landing area...
 - 
    
  
  § 38.159(b)(7) Platform gaps
  
is at vehicle floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and the vehicle floor shall not exceed 1/2 inch (13 mm) horizontally...
 - 
    
  
  Invisible Wounds: Emerging Promising Practices for Meeting Planners
  
Big crowds, loud noises, blocked line of sight to exits, and many other typical features of events can be so uncomfortable that some people will simply withdraw....
 - 
    
  
  1132A.8 Hand-activated door hardware
  
Locked exit doors shall operate consistent with Section 1132A.6, in the direction of egress....
 - 
    
  
  Chapter 6 BUILDING AN EVACUATION PLAN FOR A PERSON WITH A COGNITIVE DISABILITY
  
Possible accommodations for people with cognitive disabilities might include the following: Providing a picture book of drill procedures Color coding fire doors and exit...
 - 
    
  
  III-7.5115 Elevators and platform lifts
  
Lifts must permit unassisted entry, operation, and exit....
 - 
    
  
  Education for All Handicapped Children Act/Individuals with Disabilities Education Act
  
The Act is renamed the Individuals with Disabilities Education Act (IDEA) in 1990, and amendments in 1997 add a focus on transition outcomes for students with disabilities exiting high school...
 - 
    
  
  Escalators
  
criteria require steps to be demarcated by yellow lines 2” wide maximum along the back and sides (§6.1.3.5.6) and specify at least 2, but no more than 4, flat steps at escalator entrances and exits...
 - HEWI Hinged Support Rail Duo
 - Sargent HP Bored Lock with Push/Pull Trim
 - Landscape Forms Inc. Parc Vue Bench Collection
 - Mockett PCS49B Rectangular Power Grommet
 - 
    
  
  1007.8 Exterior area for assisted rescue
  
Where walls or openings are between the area for assisted rescue and the interior of the building, the building exterior walls within 10 feet (3048 mm) horizontally of a nonrated wall or...
 - 
    
  
  903.4 Back Support
  
Back support shall be 2 1/2 inches (64 mm) maximum from the rear edge of the seat measured horizontally. Advisory 903.4 Back Support....
 - 
    
  
  704.10 Vertical exposure
  
lot, approved protectives shall be provided in every opening that is less than 15 feet (4572 mm) vertically above the roof of an adjoining building or adjacent structure that is within a horizontal...
 - 
    
  
  1003.2.13.7 Exterior area for assisted rescue
  
Where walls or openings are between the area for assisted rescue and the interior of the building, the building exterior walls within 10 feet (3048 mm) horizontally of a nonrated wall or...
 - 
    
  
  4. Summary of Practice
  
The profile must be represented as a series of elevation values taken along with a series of horizontal distance values along the wheel track. 4.3 The PRI scale starts at zero for a surface...
 - 
    
  
  How is slip resistance measured?
  
The coefficient of friction between the two surfaces is the ratio of the horizontal and vertical forces required to move one surface over another to the total force pressing the two surfaces...