Recommendations: Consider additional space on the narrow dimension to allow alternative transfers. Some people may need to fully recline to dress or change clothes....
Search Results "Minimum Dimension"
-
Clear Floor Space [4.35.2]
-
4.3.4 Knee and Toe Clearances
The following dimensions on knee and toe clearances should be used to accommodate 95% of our study sample on all four dimensions: • Toe clearance depth: 127 mm (5 in.) maximum, measured...
-
Introduction
First, as defined in Section 104.1.1 and clarified in its advisory, they are intended to apply only to certain sections of the 2010 ADA Standards where dimensions are stated as single dimensions...
-
Bus Stop Pads
The proposed rule specified that these dimensions were required to "the maximum extent allowed by legal or site constraints" (1002.2.2)....
-
Technical Requirements for Accessible Hiker/Pedestrian Trails
All of these requirements are minimums....
-
11B-903.4 Back support
The bench shall provide for back support or shall be affixed to a wall along its long dimension....
-
DETR
A checkerboard was mounted behind the stand from which dimensions could be scaled from photographs....
-
Extremely well done!
This video clearly demonstrates the length and dimension of what is expected but often misunderstood by contractors and architects....
-
11B-609.3 Spacing
The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
-
11B-609.3 Spacing
The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
-
11B-609.3 Spacing
The space between the grab bar and projecting objects below and at the ends shall be 1½ inches (38 mm) minimum....
-
Clear Floor or Ground Space: ADA Standard Section 1008.4.2
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
11B-1008.4.2 Clear floor or ground space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
11B-1008.4.2 Clear floor or ground space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
Bottom Dollars | A Rooted in Rights Original Documentary
When the Fair Labor Standards Act passed in 1938, it included a revolutionary civil rights protection: a minimum wage....
-
T303 Handrails, Stanchions, and Handholds
In the 2010 NPRM, we proposed that gripping surfaces with circular cross sections (such as those used on seat-back handholds) have an outside diameter of 1 1/4 inches minimum and 2 inches...
-
11B-703.4.2 Location
Signs containing tactile characters shall be located so that a clear floor space of 18 inches (457 mm) minimum by 18 inches (457 mm) minimum, centered on the tactile characters, is provided...
-
11B-703.4.2 Location
Signs containing tactile characters shall be located so that a clear floor space of 18 inches (457 mm) minimum by 18 inches (457 mm) minimum, centered on the tactile characters, is provided...
-
11B-302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel. Advisory 11B-302.3 Openings....
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and that the lift platform accommodate a wheelchair measuring 30 inches by 48 inches....
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and that the lift platform accommodate a wheelchair measuring 30 inches by 48 inches....
-
Truncated Domes
In the final rule, the Board has revised the specification for the diameter and spacing of truncated domes to permit a range of dimensions (705.1.1)....
-
R103.1 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range. Advisory R103.1 Conventional Industry Tolerances....
-
1. Abdomen depth (AD)
dimensions are unrestricted or unbounded....