Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface. EXCEPTIONS: 1....
Search Results "Minimum Dimension"
Commonly Searched Documents
-
505.6 Gripping Surface
-
11B-505.6 Gripping surface
Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface. Exceptions: 1. ...
-
REDUCTION AND ANALYSIS OF DATA
The ADAAG set minimum criteria for accessibility of pedestrian facilities throughout the United States....
-
R302.7.3 Horizontal Openings
Elongated openings in gratings shall be placed so that the long dimension is perpendicular to the dominant direction of travel....
-
A4.2.4 Clear Floor or Ground Space for Wheelchairs
A3 represent typical dimensions for a large adult male. The space requirements in this guideline are based upon maneuvering clearances that will accommodate most wheelchairs. Fig....
-
Perpendicular Curb Ramps (R304.2) (Section-by-Section Analysis)
The turning space must be 1.2 meters (4 feet) minimum by 1.2 meters (4 feet) minimum, and is permitted to overlap other turning spaces and clear spaces....
-
Introduction
Introduction This memo provides a revised description and analyses examining knee clearance dimensions in mammography equipment (as requested in your email dated: 4/15/2013)....
-
11B-604.9 Water closets and toilet compartments for children's use
Clarifies that when the suggested dimensions for children are used, the requirements for a single age group shall be applied consistently to the installation of a water closet and all associated...
-
4.1.3(12)(a)
Additional storage may be provided outside of the dimensions required by 4.25....
-
A4.2.4 CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS
A3 represent typical dimensions for a large adult male. The space requirements in this standard are based upon maneuvering clearances that will accommodate most larger wheelchairs....
-
4.1.2(11)
Additional storage may be provided outside of the dimensions shown in Fig 38....
- Corbin Russwin Inc. DC46900 Series Safeguard Door Closers
-
9.2.2(4)
Additional storage may be provided outside of the dimensions required by 4.25....
-
5.8.2.1 Height of Breast Platform at Time of Measurement
Industry started with this dimension and determined the proportionate height of the breast platform to be 34 inches....
-
C. Parking Slope
.: when measured as shown on the Tools & Techniques page , is the critical dimension 1/2" or less)?...
-
302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel....
-
G. Drop-off Area
If the lodging facility has covered passenger pickup/drop-off areas, does the pavement at such area(s), including the required 5' wide access aisle, slope 1:50 or less (critical dimension...
-
4.4.1 Overview of Mammography Accessibility Considerations
Ordinarily, the accessibility dimensions are static and are measured from a static element, such as the floor....
-
1018.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
5.3.2 Transfer Sides Recommendations for M301
Patients who use mobility devices would have the choice to approach parallel to the deep dimension of the transfer surface, parallel to the wide dimension of the transfer surface, or at...
-
Notes:
Given the differing shapes of mammography devices, defining the dimensions in relationship to each other with a static measurement point for the breast platform assures accessibility despite...
-
Gratings [4.5.4]
ADAAG requires a maximum opening dimension of ½ inch in one direction and that elongated openings be placed so that the long dimension is perpendicular to the dominant direction of travel...
- Stanley SB600 Bifolding Door
-
1017.6 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....