Where physical or safety constraints prevent the deployment at some stops of a lift having its long dimension perpendicular to the car axis, the transportation entity may specify a lift...
Search Results "Minimum Dimension"
-
§ 38.125(b)(2)(ii) Exception
-
§ 38.83(b)(2)(ii) Exception
Where physical or safety constraints prevent the deployment at some stops of a lift having its long dimension perpendicular to the vehicle axis, the transportation entity may specify a lift...
-
§ 38.95(b)(2)(ii) Exception
Where physical or safety constraints prevent the deployment at some stops of a lift having its long dimension perpendicular to the car axis, the transportation entity may specify a lift...
-
Clear Width of Circulation Paths and Maneuvering Clearances at Wheelchair Spaces
In the 2010 NPRM, the Access Board proposed specific minimum dimensions for the clear width of circulation paths within non-rail vehicles, as well as maneuvering clearances at wheelchair...
-
Technical Requirements
Are the specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
4.10.12(1)
All control buttons shall be at least 3/4 in (19 mm) in their smallest dimension. They shall be raised or flush....
-
4.10.12(1)
All control buttons shall be at least 3/4 in (19 mm) in their smallest dimension. They may be raised or flush....
-
Technical Requirements
The specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.). ...
-
Seeger et al.
Both unoccupied and occupied dimensions of device width and length were measured as well as a set of other basic dimensions....
-
4.1.2 Surface Design of Examination Tables and Chairs
Thus, contouring must be addressed in considering minimum height standards for accessibility of transfer surfaces (Section 5.1.4)....
-
§382.133(e)(2)
(2) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with FAA safety requirements...
-
T102.1 Calculation of Percentages
Where the determination of the required size or dimension of an element involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
Technical Requirements
Technical Requirements—Specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
A4.22.3 Clear Floor Space
Figure 28 (section 4.16) provides minimum clear floor space dimensions for toilets in accessible “unisex” toilet rooms....
-
§27.71(h)(1)
(1) Airports must consult with one or more service animal training organizations regarding the design, dimensions, materials and maintenance of service animal relief areas;...
-
T602 Wheelchair Spaces
Wheelchair spaces must also be 30 inches minimum in width and 48 inches minimum in length. See T602.4....
-
Toto Site Review: A Criteria-Based Evaluation Framework
A User Protection Platform Rating approach helps quantify this dimension by comparing how effectively these safeguards are implemented relative to stated standards....
-
Mayer-Rothschild Foundation: Determination of Grab Bar Specifications for Independent and Assisted Transfers in Residential Care Settings
The purpose of this project is to identify, both objectively and subjectively, the spatial and configurational dimensions of grab-bars that effectively support both independent standing...
-
Fur out the wall
The centerline of the water closet shall be 16 inches (405 mm) minimum to 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430...
-
§382.133(f)(3)
(3) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with the safety regulations...
-
5. Curb Ramp Running Slope
5. ...do the curb ramps have running slopes of 1:12 or less (critical dimension of 2" or less)?...
-
7. Exterior Ramp Running Slope
7. ...do the exterior ramps have running slopes of 1:12 or less (critical dimension of 2" or less)?...
-
Figures in the Standards
Figures in the ADA Standards are provided only for informational purposes to illustrate dimensions and requirements contained in the text....
