Wheelchair spaces must also be 30 inches minimum in width and 48 inches minimum in length. See T602.4....
Search Results "Minimum Dimension"
Filters
Commonly Searched Documents
-
T602 Wheelchair Spaces
-
Inpro Corporation ENDURANT® Trench Drain Receptor
emitting products Has been tested and meets the GREENGUARD Children & School chemical emissions levels Depth of trench drain shower receptor is customizable with a minimum...
-
Extremely well done!
This video clearly demonstrates the length and dimension of what is expected but often misunderstood by contractors and architects....
-
§ 38.125(b)(2)(ii) Exception
Where physical or safety constraints prevent the deployment at some stops of a lift having its long dimension perpendicular to the car axis, the transportation entity may specify a lift...
-
§ 38.83(b)(2)(ii) Exception
Where physical or safety constraints prevent the deployment at some stops of a lift having its long dimension perpendicular to the vehicle axis, the transportation entity may specify a lift...
-
§ 38.95(b)(2)(ii) Exception
Where physical or safety constraints prevent the deployment at some stops of a lift having its long dimension perpendicular to the car axis, the transportation entity may specify a lift...
-
EZJamb SlideSet Modern Pocket Door Frame System
The SlideSet Flush Finish Pocket Door System has been designed to provide the absolute minimum of detail giving the ability to completely conceal the door and give the impression that the...
-
Introduction
Introduction The following memo is a brief analysis of the wheelbase dimension for wheeled mobility devices in the anthropometry of wheeled mobility database....
-
M301.2.2 Transfer Surface Size
The minimum size of the transfer surface is 28 inches wide minimum and 21 inches deep minimum and is located such that the long dimension of 28 inches is be located parallel to the patient...
-
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301)
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301) The Committee recommends a transfer surface size on imaging equipment be a minimum of 28 inches long by a minimum...
-
Seeger et al.
Both unoccupied and occupied dimensions of device width and length were measured as well as a set of other basic dimensions....
-
Technical Requirements
Are the specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
4.10.12(1)
All control buttons shall be at least 3/4 in (19 mm) in their smallest dimension. They shall be raised or flush....
-
4.10.12(1)
All control buttons shall be at least 3/4 in (19 mm) in their smallest dimension. They may be raised or flush....
-
Technical Requirements
The specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.). ...
-
T-turn Maneuvering Space
The Department has decided to delete the reference to the T-turn dimensions in the Guidelines for Requirement 4....
-
Size and Spacing of Grab Bars and Handrails [4.26.2]
The 1½ inch clearance between walls and handrails or grab bars is an absolute dimension; it provides knuckle clearance while generally disallowing entrapment of the forearm or elbow....
-
Alterations: Alternate Stalls
Wheelchair maneuvering and transfer can be very difficult or impossible within these dimensions which is why these designs are permitted only in alterations where "technical infeasibility...
-
11B-505.6 Gripping surface
Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface....
-
11B-1008.4.2 Clear floor or ground space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
§382.133(e)(2)
(2) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with FAA safety requirements...
-
T102.1 Calculation of Percentages
Where the determination of the required size or dimension of an element involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
Technical Requirements
Technical Requirements—Specific numbers, conditions, and measurements that are required to be achieved (percent that must comply, dimensions, reach ranges, grades, trail width, etc.)....
-
§27.71(h)(1)
(1) Airports must consult with one or more service animal training organizations regarding the design, dimensions, materials and maintenance of service animal relief areas;...
