The size of the clear ground space is based on the dimensions for maneuvering clearance at clear floor or ground spaces that are confined on all or part of three sides in 305.7 of the Architectural...
Search Results "Minimum Dimension"
-
1011.2.1 Size and Location
-
407.12.3.2.2 Knee and Toe Space (Section-by-Section Analysis)
407.12.3.2.2 Knee and Toe Space (Section-by-Section Analysis) This section proposes dimensions for knee and toe space under ICT when an obstructed forward reach is provided....
-
Clear Floor Space [4.16.2]
Clear Floor Space [4.16.2] ADAAG (Figure 28) specifies the amount of space required at an accessible toilet, not the minimum room size, which must also include turning space, clear floor...
-
14.3 Q...are there any requirements for the inside dimensions of these individual parking garages?
A. Yes. These garages would be public and common use space, even though the individual garages may be assigned to a particular dwelling unit. Therefore, at least two percent of the...
-
Standing Supports (M304.3 and M305.3)
The minimum and maximum height of the bottom of the support above the standing surface is based on anthropometric data for the 1th percentile woman (minimum) and the 99th percentile man...
-
5.2.1.4 Transfer Surface Size for Imaging Equipment
The transfer surface should be 28 inches wide minimum and 21 inches deep minimum....
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
5.2.2.2 Transfer Surface Depth Recommendation for M302
5.2.2.2 Transfer Surface Depth Recommendation for M302 The Committee recommends a minimum depth requirement of 17 inches for equipment used by patients in seated positions....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-411.2.1.5.1 Size
Buttons shall have square shoulders, be 3/4 inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding...
-
11B-411.2.1.5.1 Size
Buttons shall have square shoulders, be 3/4 inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding...
-
11B-411.2.1.5.1 Size
Buttons shall have square shoulders, be 3/4 inch (19.1 mm) minimum in the smallest dimension and shall be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding...
-
Construction Specification Institute
For longitudinal lines, measurements were to be taken in minimum 5 - foot lengths running parallel to the long dimension, with one measurement line per 3 feet of width and within 2 feet...
-
Platform Size and Surface
The minimum dimensions are based on the approach. Where entry and exit are on the narrow dimension, the space must be at least 36 inches wide and at least 48 inches long....
-
1.1.7 Measurement of parking areas
These areas should be considered as a pedestrian walk with a minimum width of 60 in. and a length of approximately 20 ft and with an ADA/ABA - AG maximum slope of 1:48 in both directions...
-
5.9.2.1 Standing Supports on Single Ramped Entry Raised Platforms with Wheelchair Spaces Recommendations
The length of the standing supports must be 80% of the platform length or 32-inches minimum, from the platform entry edge....
-
5.8.2.4 Unobstructed Floor Space Recommendation
5.8.2.4 Unobstructed Floor Space Recommendation The Committee recommends the unobstructed floor space in front of the base support be a minimum of 17 inches deep....
-
M301.4 Lift Compatibility
high minimum measured from the floor, and 36 inches (915 mm) deep minimum measured from the edge of the examination surface....
-
10.3.1(17)
EXCEPTION: Elevator cars with a clear floor area in which a 60 inch diameter circle can be inscribed may be substituted for the minimum car dimensions of 4.10, Fig. 22....
-
11B-812.6 Vehicle spaces
Vehicle spaces serving van accessible, standard accessible, ambulatory and drive-up EVCS shall be 216 inches (5486 mm) long minimum and shall comply with Sections 11B-812.6.1 through 11B...
-
11B-812.6 Vehicle spaces
Vehicle spaces serving van accessible, standard accessible, ambulatory and drive-up EVCS shall be 216 inches (5486 mm) long minimum and shall comply with Sections 11B-812.6.1 through 11B...
-
407.12.1.1 Vertical Plane for Side Reach (Section-by-Section Analysis)
407.12.1.1 Vertical Plane for Side Reach (Section-by-Section Analysis) This section proposes that, where a side approach is provided, the vertical reference plane must have a minimum...
-
Accessible Pathway & Corridor: Minimum Clear Width Required for 180-degree Turn Around Barrier
The minimum space required to perform a complete 180-degree turn around an obstruction within moving or knocking down any of the walls was recorded....
-
Urinal Depth
In the proposed rule, the Board sought to clarify the requirement in the original ADAAG that accessible urinals have an "elongated" rim by specifying a minimum dimension of 13 ½ inches,...