Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
Search Results "Minimum Dimension"
-
608.2.1 Transfer Type Shower Compartments
-
Conclusions
Conclusions The proposed guidelines for medical diagnostic equipment currently recommend a minimum transfer surface 30 in. (760mm) wide and 15 in. (381mm) deep....
-
Baby Changing Tables
The specified dimensions of toilet compartments provide the minimum amount of space necessary for wheelchair maneuvering into the compartment, positioning at the fixture, and exit from the...
-
Exceptions Considered for Wheelchair Spaces on Raised Platforms
This dimension is based on provisions in the 2004 ADA and ABA Accessibility Guidelines that allow accessible routes, which normally must be 36 inches wide minimum, to be 32 inches wide minimum...
-
Grab Bar Cross Sections
Non-circular cross sections were to have maximum cross section dimensions of 2 inches, a perimeter dimension between 4 and 4‒11/16 inches, and edges with a c inch minimum radius....
-
Is there a minimum number of risers a stairway must have for it to be covered?
No, the Standards apply to any stairs that are part of a means of egress regardless of the number of risers.
-
5.4.6 Transfer Support Gripping Surface Cross Section and Clearances for M301, M302, and M305.2
transfers: Grab bars with circular cross sections must have an outside diameter of 1¼ inches minimum and 2 inches maximum....
-
4.1.6(4)(c)
(ii) Where existing shaft or structural elements prohibit strict compliance with 4.10.9, then the minimum floor area dimensions may be reduced by the minimum amount necessary, but in no...
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
Figure 408.4.1(c) Limited-Use/Limited-Application (LULA) Elevator Car Dimensions – Drawing from the U.S. Access Board
-
Figure 408.4.1(b) Limited-Use/Limited-Application (LULA) Elevator Car Dimensions – Drawing from the U.S. Access Board
-
R304.3.1 Turning Space
A turning space 1.2 m (4.0 ft) minimum by 1.2 m (4.0 ft) minimum shall be provided at the bottom of the curb ramp and shall be permitted to overlap other turning spaces and clear spaces....
-
10. Can a transfer platform be an irregular shape as long as it incorporates the minimum rectangle of 14 by 24 inches?
Can a transfer platform be an irregular shape as long as it incorporates the minimum rectangle of 14 by 24 inches? Yes....
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
11B-703.7.2.1 International Symbol of Accessibility
A border may be provided inside or outside of the minimum required International Symbol of Accessibility dimension....
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
11B-703.7.2.1 International Symbol of Accessibility
A border may be provided inside or outside of the minimum required International Symbol of Accessibility dimension....
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
T505.3 Location of Operable Parts
Operable parts shall be located so that they are reachable by passengers using wheelchair when parked in a clear space 30 inches (760 mm) wide minimum and 48 inches (1220 mm) long minimum...
-
M305.3 Standing Supports (Section-by-Section Analysis)
and whether standing supports can provide a 1½ inch minimum clearance around the gripping surface....
-
Introduction
Introduction The proposed guidelines for medical diagnostic equipment recommends a minimum transfer surface 30 in. (760mm) wide and 15 in. (381mm) deep. At the request of the U.S....
-
Accessible Pathway & Corridor: Minimum Clear Floor Space Required for 360-degree Turn
The minimum space required to perform a complete 360-degree turn within moving or knocking down any of the walls was recorded....
-
Knee & Toe Space [M303.2.4]
25-inch absolute dimension....
-
Graphic Conventions [3.1]
Dimensions in ADAAG and this manual are absolute unless noted as a maximum or minimum. ADAAG includes in text and figures the metric equivalent (in millimeters)....
