Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
Search Results "Minimum Dimension"
-
11B-608.2.2 Standard roll-in type shower compartments
-
5.8.2 Knee and Toe Clearance Recommendations under Breast Platform Recommendations
Table 5.8.2(a) Recommended Dimensions for Knee and Toe Clearances Proposed Dimensions Based on 2010 Standards Dimensions Recommended by Wheeled Mobility Anthropometry...
-
R409.7.2 Non-Circular Cross Sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 100 mm (4 in) minimum and 160 mm (6.25 in) maximum, and a cross-section dimension of 57 mm...
-
Cross Section of Gripping Surfaces
during transfers: • Grab bars with circular cross sections must have an outside diameter of 1¼ inches minimum and 2 inches maximum...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
Knee and Toe Clearance (M303.2.4)
M303.2.4 would require the depth of wheelchair spaces to include knee and toe clearance of 17 inches minimum and 25 inches maximum....
-
Section 36.303(g)(4) Minimum Requirements for Audio Description Devices
In the NPRM, the Department proposed at § 36.303(g)(3)(ii)(A) that movie theaters maintain one audio description device per auditorium, with a minimum of two devices per movie theater....
-
Seat [4.21.3]
Seat [4.21.3] ADAAG specifies maximum seat dimensions. Minimum dimensions contained in the CABO-ANSI A117.1‒1992 standard are acceptable....
-
505.7.2 Non-Circular Cross Sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (100 mm) minimum and 6 1/4 inches (160 mm) maximum, and a cross-section dimension...
-
505.7.2 Non-Circular Cross Sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (100 mm) minimum and 6 1/4 inches (160 mm) maximum, and a cross-section dimension...
-
407.4.6.2.1 Size
Buttons shall be ¾ inch (19 mm) minimum in their smallest dimension....
-
608.2.1 Transfer Type Shower Compartments
mm) wide minimum entry on the face of the shower compartment....
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
11B-609.2.2 Non-circular cross section
Grab bars with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (102 mm) minimum and 4.8 inches (122 mm)...
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-409.4.6.1 Size
Control buttons shall be ¾ inch (19.1 mm) minimum in their smallest dimension....
-
11B-409.4.6.1 Size
Control buttons shall be ¾ inch (19.1 mm) minimum in their smallest dimension....
-
11B-409.4.6.1 Size
Control buttons shall be ¾ inch (19.1 mm) minimum in their smallest dimension....
-
Transfer Surface Size: Equipment Used by Patients in Supine, Prone, or Side-Lying Position (M301.2.2)
minimum....
-
11B-405.7.2.1
Top landings shall be 60 inches (1524 mm) wide minimum. Advisory 11B-405.7.2.1 Top landing width....
-
11B-405.7.2.1
Top landings shall be 60 inches (1524 mm) wide minimum. Advisory 11B-405.7.2.1 Top landing width....
-
407.4.6.2.1 Size
Buttons shall be ¾ inch (19 mm) minimum in their smallest dimension....
-
407.4.6.2.1 Size
Buttons shall be 3/4 inch (19 mm) minimum in their smallest dimension....