Detectable warnings shall consist of a surface of truncated domes and shall comply with Section 11B-705....
Search Results "Side Transfer Surface"
-
11B-705.1.1 General
-
11B-903.7 Wet locations
Where installed in wet locations, the surface of the seat shall be slip resistant and shall not accumulate water....
-
11B-903.7 Wet locations
Where installed in wet locations, the surface of the seat shall be slip resistant and shall not accumulate water....
-
11B-705.1.1 General
Detectable warnings shall consist of a surface of truncated domes and shall comply with Section 11B-705....
-
CURB CUT
[DSA-AC] An interruption of a curb at a pedestrian way, which separates surfaces that are substantially at the same elevation....
-
Position of Grab Bars: ADA Standard Section 609.4
Section 609.4 covers the current ADA Standards for the position of grab bars.
-
805.3 Clear Floor or Ground Space
A clear floor space complying with 305 shall be provided on each side of the bed. The clear floor space shall be positioned for parallel approach to the side of the bed....
-
11B-604.8.2.3 Grab bars
A side-wall grab bar complying with Section 11B-604.5.1 shall be provided on both sides of the compartment....
-
Road Roughness Measurements
One of the original methods was the profilograph, which was adopted in the early 1900’s, and can directly measure surface roughness by using an array of wheels on each side to establish...
-
KEEP Clear of WheelChair Ramps Video
Requires the Registered User plan or above. Login! -
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-231.4.1 Cubicles and counters
At least 5 percent, but no fewer than one, of cubicles shall comply with Section 11B-902 on both the visitor and detainee sides....
-
608.2.2.1 Clearance
EXCEPTION: A lavatory complying with 606 shall be permitted on one 30 inch (760 mm) wide minimum side of the clearance provided that it is not on the side of the clearance adjacent to the...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-231.4.1 Cubicles and counters
At least 5 percent, but no fewer than one, of cubicles shall comply with Section 11B-902 on both the visitor and detainee sides....
-
11B-232.5.1 Cubicles and counters
At least 5 percent, but no fewer than one, of cubicles shall comply with Section 11B-902 on both the visitor and detainee sides....
-
4.34.6.7* OVENS
For side-opening ovens, the door latch side shall be next to the open counter space, and there shall be a pull-out shelf under the oven extending the full width of the oven and pulling out...
-
404.2.4.2 Doorways without Doors or Gates
unless noted) From front 48 inches (1220 mm) 0 inches (0 mm) From side 1 42 inches (1065 mm)...
-
1134A.7, Item 2
Where the water closet is not placed adjacent to a side wall capable of accommodating a grab bar, the bathroom shall have provisions for installation of floor-mounted, foldaway or similar...
-
1134A.7, Item 2
Where the water closet is not placed adjacent to a side wall capable of accommodating a grab bar, the bathroom shall have provisions for installation of floor-mounted, foldaway or similar...
-
Door Maneuvering Clearance
, hinge side)....
-
11B-404.2.4.1 Swinging doors and gates
CLEARANCES AT MANUAL SWINGING DOORS AND GATES TYPE OF USE MINIMUM MANEUVERING CLEARANCE Approach direction Door or gate side...
-
Perpendicular Curb Ramps (R304.2) (Section-by-Section Analysis)
The flared sides are part of the pedestrian circulation path, but are not part of the pedestrian access route. The slope of the flared sides is measured parallel to the curb line....
-
11B-604.8.1.2 Doors
A door pull complying with Section 11B-404.2.7 shall be placed on both sides of the door near the latch. ...