Toe/knee clearance below the unit makes this reach easier by allowing a closer approach....
Search Results "Clearance in Base"
Commonly Searched Documents
-
Forward Approach
- Inclusion Solutions Offset Door Hinge
-
UNREASONABLE HARDSHIP
[DSA-AC] When the enforcing agency finds that compliance with the building standard would make the specific work of the project affected by the building standard infeasible, based on an...
-
11B-403.5.3 Passing spaces
a space 60 inches (1524 mm) minimum by 60 inches (1524 mm) minimum; or, an intersection of two walking surfaces providing a T-shaped space complying with Section 11B-304.3.2 where the base...
-
11B-1009.2 Pool lifts
Pool lift seats that consist of materials that resist corrosion and provide a firm base to transfer will be usable by a wider range of people with disabilities....
-
4.3.5.2 180-degree turn
4.3.5.2 180-degree turn Currently, the ADA-ABA does not have a specific clearance for this type of turn. The 1525 mm (60 in.) turning space would be used instead....
-
11B-307.4.1 Guy braces
FIGURE 11B-307.4.1 GUY BRACES FIGURE 11B-307.4 VERTICAL CLEARANCE...
-
E2-3. Interior Stairs
., protected with a cane-detectable warning or a barrier that prevents travel into the area with less than an 80-inch-high head clearance)? [ADA Stds 4.4.2] Yes _____ No _____...
-
16(a)(v)
(v) The accessible rooms for individuals with mobility disabilities have the maneuvering clearances for beds specified in ADA Standards §9.2.2(1), to and within the bathroom (ADA Standards...
- Don-Jo Mfg., Inc. Pull Plate CFC7015
-
"Direct Threat" to Self
However, as emphasized above, such determinations must be strictly based on valid medical analyses or other objective evidence related to this individual, using the factors set out above...
-
What obligations does an employer have to provide health insurance to employees with HIV or AIDS?
Insurance distinctions that are not based on disability, however, and that are applied equally to all insured employees, do not discriminate on the basis of disability and do not violate...
-
4.2.5* Forward Reach
If the high forward reach is over an obstruction, reach and clearances shall be as shown in Fig. 5(b)....
-
4.34.5.3 LAVATORY, MIRRORS, AND MEDICINE CABINETS
(2) If a cabinet is provided under the lavatory in adaptable bathrooms, then it shall be removable to provide the clearances specified in 4.22.6....
-
Are doors or gates to employee work areas required to comply?
Entry doors or gates to employee work areas are required to meet applicable requirements, including those for maneuvering clearance, on the exterior, but not the interior....
-
11B-604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door...
-
11B-604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door...
-
11B-809.10.8.1 Location
Lavatories without base cabinets shall be installed with the centerline 18 inches (457 mm) minimum from an adjoining wall or fixture to allow for forward approach....
-
Shower and Sauna Doors in Transient Lodging Facilities
The exemption to the section 224.1.2 requirement for a 32-inch wide clearance at doors to shower and saunas applies only to those showers and saunas in guest rooms which are not required...
-
§ 37.42(c)(5)
(5) Station-based lifts;...
-
§ 37.42(c)(5)
(5) Station-based lifts;...
-
Pool Lifts: ADA Standard Section 1009.2
Pool lift seats that consist of materials that resist corrosion and provide a firm base to transfer will be usable by a wider range of people with disabilities....
-
11B-812 Electric vehicle charging stations
ETA Editor's Note EVCS are not addressed by 2010 ADA Standards, although a case could be made, based on the general obligation for governments to make their services, programs...
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....