Rectangular Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order....
Search Results "Clearance in Base"
Filters
Commonly Searched Documents
-
Hager Companies Rectangular Wrought Door Pull 2
-
11B-410.7 Landing size
ETA Editor's Note There are no requirements for landing size in 2010 ADA Standards, although the door maneuvering clearance requirements at 404.2.4 should be applicable outside the platform...
-
705.1.2 Dome Spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
11B-604.8.1.2 Doors
Doors shall not swing into the clear floor space or clearance required for any fixture....
-
Hager Companies Modified Half Round Wrought Door Pull 1
Modified Half Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special order....
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements, and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
Paperwork Reduction Act
This rule does not contain any paperwork or record keeping requirements and does not require clearance under the PRA....
-
11B-604.8.1.1.1 Maneuvering space with in-swinging door
In a wheelchair accessible compartment with an in-swinging door, a minimum 60 inches (1524 mm) wide by 36 inches (914 mm) deep maneuvering space shall be provided in front of the clearance...
-
11B-705.1.1.2 Dome spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
11B-404.3 Automatic and power-assisted doors and gates
An automatic door may be used as equivalent facilitation when it is technically infeasible to provide sufficient strike-side clearance for code compliance, but a power-assisted door may...
-
SmartCells Flooring: Softer Anti-Fatigue Mats are NOT Better
SATECHinc.com/media/softer Many anti fatigue mats on the market today are based off of the assumption that softer is better....
-
Just Manufacturing Ledgemount Swivel Gooseneck Mixing Faucet
Swiveling gooseneck spout with 7-3/8" clearance. Replaceable seats. Brass quarter turn quick compression stem units. Replaceable reinforced nitrile rubber packing....
-
Notes:
Otherwise,, it is quite possible to configure a piece of equipment that meets all the clearances yet does not provide accessibility if there is not a defined method of measuring the clearances...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
Dumpster Enclosures
Dumpster Enclosures Dumpster enclosures used exclusively by employees shall be considered employee work areas based on TAS 201.1; therefore, they must comply with TAS 203.9....
-
Technical Memorandum TM 2013-15 Baby Changing Tables
TM 2013-15 Baby Changing Tables Effective Date: June 1, 2013 2012 TAS Reference: 902 Baby changing tables are work surfaces based on Advisory 902.1; therefore, if fixed...
-
Pilot Rock WXT and WXTH Picnic Table Using Lumber
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table Using Recycled Plastic
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table Using Formed Steel Channel
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WXT and WXTH Picnic Table Using Recycled Plastic
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WXT and WXTH Picnic Table Using Expanded Steel
The WXT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
-
Pilot Rock WUT and WUTH Picnic Table Using Lumber
The WUT Series offers clearances under the table top of 30” wide, 27” high, and 24” total knee and toe clearance (19” knee and 5” toe). Nominal seat height is 18”....
