102 Dimensions for Adults and Children The technical requirements are based on adult dimensions and anthropometrics....
Search Results "Clearance in Base"
Filters
Commonly Searched Documents
-
102 Dimensions for Adults and Children
-
11B-705.1.1.2 Dome spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
Hager Companies Round Offset Door Pull 23Q
Round Offset Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special orders....
-
Hager Companies Round Wrought Door Pull 5D
Round Wrought Door Pull Materials: - Aluminum, brass, bronze, stainless steel Accessible: - 2-1/2" (64 mm) Clearance available on special orders....
-
11B-805.6 Hand washing fixtures, lavatories and sinks
Knee clearance requirement - All accessibility requirements of Section 11B-606 apply to lavatories, sinks and handwashing fixtures required to be accessible....
-
11B-805.6 Hand washing fixtures, lavatories and sinks
Knee clearance requirement - All accessibility requirements of Section 11B-606 apply to lavatories, sinks and handwashing fixtures required to be accessible....
-
Shower Dimensions for ADA
This means the prevailing dimension of the shower is 3’ X 5’ but in some cases there is a dimension at the base of the shower that is slightly less than that due to thresholds, shower base...
-
Truncated Domes
The proposed rule specified that the truncated domes have a diameter of 0.9 inch, measured at the base....
-
Paperwork Reduction Act
This rule does not contain any paperwork or recordkeeping requirements and does not require clearance under the PRA....
-
Accessible Route Into and Through the Business
Customers with disabilities will not be able to shop in a store if the route through an entry plaza is too narrow because of a display of snow blowers, if the maneuvering clearance alongside...
-
705.1.2 Dome Spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
705.1.2 Dome Spacing
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
SECTION#4
SECTION#4 For the following questions, please answer every item pertaining to the sub-base installation, if the sub-base installation was necessary due to the installation of the trail...
-
Table Surface Height
Some commenters also recommended a higher minimum height of 29 inches instead of 28 inches to allow a more comfortable knee clearance. Response....
-
Amusement Rides with Wheelchair Spaces
Amusement Rides with Wheelchair Spaces Minimum space requirements and clearances for wheelchairs are specified where a ride provides a wheelchair space....
-
Paperwork Reduction Act
This rule does not contain any paperwork or recordkeeping requirements and does not require clearance under the PRA....
-
Reading and Study Areas [8.2]
Recommendation: Specifications in 4.32, including clear passage for accessible routes, knee clearances and surface height (34 inch maximum) should be considered for movable furnishings as...
-
11B-809.12 Electrical receptacles, controls and switches
When the reach is over a kitchen work surface and base cabinet, the work surface shall be 36 inches (914 mm) maximum above the finish floor and 25 1/2 inches (650 mm) maximum in depth....
-
3. The risk must be current, not one that is speculative or remote
The risk must be current, not one that is speculative or remote The employer must show that there is a current risk -- "a high probability of substantial harm" -- to health or safety based...
-
Passing Spaces: ADA Standard Section 403.5.3
Section 403.5.3 covers the current ADA Standards for passing spaces that are part of an accessible route.
-
11B-407.4.7.2 Keypads
The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 11B-703.3.1....
-
11B-707.9.1.1 Tactilely discernible numerical keypad
A tactilely discernible numerical keypad similar to a telephone keypad containing a raised dot with a dot base diameter between 1.5 mm and 1.6 mm and a height between 0.6 mm and 0.9 mm on...
-
11B-704.2.1 Clear floor or ground space
The clear floor or ground space shall not be obstructed by bases, enclosures, or seats. Advisory 11B-704.2.1 Clear floor or ground space....
-
11B-410.7 Landing size
ETA Editor's Note There are no requirements for landing size in 2010 ADA Standards, although the door maneuvering clearance requirements at 404.2.4 should be applicable outside the platform...
