Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
Search Results "Clearance in Base"
Filters
Commonly Searched Documents
-
11B-1009.4.5 Grab bars
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
T504.1 General
Passenger access routes shall provide clearances that are sufficient to permit passengers using wheelchairs to move between wheelchair spaces and doorways that provide accessible boarding...
-
Technical Memorandum TM 2013-14 Dining Surfaces
In addition, dining surfaces must be dispersed based on TAS 226.2; therefore, each type of dining surface must comply with TAS 902....
-
1630.16(f)(2)
(2) A covered entity may establish, sponsor, observe or administer the terms of a bona fide benefit plan that are based on underwriting risks, classifying risks, or administering such risks...
-
§1630.16(f)(2)
(2) A covered entity may establish, sponsor, observe or administer the terms of a bona fide benefit plan that are based on underwriting risks, classifying risks, or administering such risks...
-
305.7.1 Forward Approach
Figure 305.7.1 Maneuvering Clearance in an Alcove, Forward Approach...
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
305.7.2 Parallel Approach
Figure 305.7.2 Maneuvering Clearance in an Alcove, Parallel Approach...
-
306.3.1 General
Space under an element between 9 inches (230 mm) and 27 inches (685 mm) above the finish floor or ground shall be considered knee clearance and shall comply with 306.3....
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
2.3.3 Comparison of Dimensions with Standards and other Anthropometric Studies
BS8300:2001 standards covered clear floor area space requirements, knee clearances and maneuvering clearances....
-
Sec.36.212(a)(2)
(2) A person or organization covered by this part from establishing, sponsoring, observing or administering the terms of a bona fide benefit plan that are based on underwriting risks, classifying...
-
12201(c)(2)
(2) a person or organization covered by this Act from establishing, sponsoring, observing or administering the terms of a bona fide benefit plan that are based on underwriting risks, classifying...
-
12201(c)(2)
(2) a person or organization covered by this chapter from establishing, sponsoring, observing or administering the terms of a bona fide benefit plan that are based on underwriting risks,...
-
§ 36.212(a)(2)
(2) A person or organization covered by this part from establishing, sponsoring, observing or administering the terms of a bona fide benefit plan that are based on underwriting risks, classifying...
-
8.2 READING AND STUDY AREAS
Clearances between fixed accessible tables and study carrels shall comply with 4.3....
-
102 Dimensions for Adults and Children
102 Dimensions for Adults and Children Section 2.1 of the 1991 Standards stated that the specifications were based upon adult dimensions and anthropometrics....
-
What kinds of racial discrimination in voting are there, and what does the Voting Rights Act do about them?
The Voting Rights Act is not limited to discrimination that literally excludes voters from the polls based on race....
-
Alterations to Accessible Units, Sleeping Rooms, and Suites [9.1.5]
Alterations to Accessible Units, Sleeping Rooms, and Suites [9.1.5] The minimum number of guest rooms required to be accessible in an alteration is based on the total number of guest...
-
11B-102 Dimensions for adults and children
The technical requirements are based on adult dimensions and anthropometrics....
-
F102 Dimensions for Adults and Children
The technical requirements are based on adult dimensions and anthropometrics....
-
11B-102 Dimensions for adults and children.
The technical requirements are based on adult dimensions and anthropometrics....
-
11B-102 Dimensions for adults and children
The technical requirements are based on adult dimensions and anthropometrics....