anthropometric study of 500 persons who use wheeled mobility devices (WMD) involved collection of demographic data, information on WMD characteristics, and structural and functional anthropometry measures...
Search Results "Mitigating Measures"
-
3.3.1 Research Data
-
T302 Walking Surfaces
With respect to slip resistance, a bus manufacturer urged the Access Board to incorporate specific measures for slip resistance (i.e., maximum and minimum friction coefficients) in the final...
-
B. Survey and Review of Polling Place Locations
If the Department concludes that the County has proposed a remedial provision that does not fully address the violation, then the Department will recommend a temporary remedial measure consistent...
-
A. Accessible Voting Program
The County agrees that the following temporary measures are reasonable and will be implemented where necessary to make an otherwise inaccessible polling place temporarily accessible on Election...
-
4.3.4 Knee and Toe Clearances
from wall • Toe clearance height: 356 mm (14 in.) minimum , measured from the floor • Knee clearance height: 711 mm (28 in.) minimum, measured from the floor • Knee clearance depth...
-
Acoustical Society of America (ASA)
A variety of fields related to sound are represented: Physics Measurement Technologies and Instrumentation Nearly All Engineering Disciplines, including...
-
903.4 Back Support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. Advisory 903.4 Back Support....
-
4. Do the carpet requirements of Section 302.2 apply to ground level accessible routes within a play area?
ASTM F 1951-99 measures the effort of work required to propel a mobility device across a surface....
-
QUESTION: UNDER WHAT CIRCUMSTANCES IS A PVO REQUIRED TO COMPENSATE A PASSENGER WITH A DISABILITY FOR LOSS OF OR DAMAGE TO A WHEELCHAIR OR OTHER ASSISTIVE DEVICE?
ANSWER: *Generally, a PVO must compensate a passenger with a disability for the full value (measured by the original purchase price) of a lost or damaged wheelchair or mobility device...
-
References:
IDeA Center Study at the University of Buffalo, New York: Summary analysis of wheelbase measurements on wheeled mobility devices....
-
Height – M301.2.1 & M302.2.1
Therefore, the report presents each of the arguments in favor of the proposed low height measurements – 19 inches, 18 inches, and 17 inches:...
-
Sec.36.309(b)(3)
auxiliary aids for persons with impaired sensory, manual, or speaking skills, unless that private entity can demonstrate that offering a particular auxiliary aid would fundamentally alter the measurement...
-
§ 36.309(b)(3)
auxiliary aids for persons with impaired sensory, manual, or speaking skills, unless that private entity can demonstrate that offering a particular auxiliary aid would fundamentally alter the measurement...
-
Clear Width [4.13.5] and Vertical Clearance
Clear Width [4.13.5] and Vertical Clearance The clear width of the opening is measured from the face of the door in a 90 degrees open position to the opposite stop....
-
R402.3 Post-Mounted Objects
pylons and the objects are 685 mm (2.25 ft) minimum and 2030 mm (6.7 ft) maximum above the finish surface, the objects shall overhang pedestrian circulation paths 100 mm (4 in) maximum measured...
-
Slope Meters and Levels
Corada has reviewed several models of slope meters and levels to assist accessibility surveyors in measuring slope and level changes....
-
Carpet [§302.2]
The standards specify the maximum pile height (1/2” measured to the backing, cushion, or pad) and texture (level or textured loop, level cut pile, or level cut/uncut pile) and require firm...
-
11B-411.2.1.2.5 Audio output
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the console....
-
11B-411.2.1.2.5 Audio output
Auditory volume shall be at least 10 dB above ambient sound level, but shall not exceed 80 dB, measured 36 inches (914 mm) in front of the console....
-
11B-604.7 Dispensers and disposal units
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
11B-411.2.1.2.3 Accessibility function button
The dots shall be spaced ¼ inch (6.4 mm), measured center to center, in the form of an equilateral triangle with a vertex pointing up....
-
903.4 Back Support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. Advisory 903.4 Back Support....
-
308.3.1 Unobstructed
Operable parts of fuel dispensers shall be permitted to be 54 inches (1370 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
Transfer Protocols
For each transfer for protocols A-C, a measurement of how high and how low a participant transferred was recorded....
