that are not required to provide mobility features complying with Section 11B-806.2 shall provide all toilet and bathing fixtures in a location that allows a person using a wheelchair measuring...
Search Results "Measuring Technique"
Filters
Commonly Searched Documents
-
11B-603.6 Guest room toilet and bathing rooms
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
R405.1 General
Clearances are measured in relation to the usable clear space, not necessarily to the vertical support for an element....
-
4.34.5.5(2) Seat
The seat shall be 17 in to 19 in (430 mm to 485 mm) high measured from the bathroom floor and shall extend the full depth of the stall....
-
What is the minimum level of slip resistance required by the standards?
This value varies according to the measurement method and protocols used. ...
-
1134A.6, Item 1.2
The shower stall shall measure at least 30 inches deep by 60 inches wide (762 mm by 1524 mm) with an entrance opening of at least 60 inches (1524 mm)....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
11B-603.6 Guest room toilet and bathing rooms
that are not required to provide mobility features complying with Section 11B-806.2 shall provide all toilet and bathing fixtures in a location that allows a person using a wheelchair measuring...
-
Q13: Are the provision and implementation of a health plan developed prior to the Amendments Act sufficient to comply with the FAPE requirements as described in the Section 504 regulation?
For example, before the Amendments Act, a student with a peanut allergy may not have been considered a person with a disability because of the student's use of mitigating measures (e.g.,...
-
Section 37.151 Waiver for Undue Financial Burden
Generally, the section allows an entity to request a wavier at any time it determines that it will not be able to meet a five-year phase-in or make measured progress toward its full compliance...
-
Notes
C Each year, the National Healthcare Disparities Reports look at different measures of disparities, such as different types of service use or different measures of patients’ experiences...
-
Access-Able Designs Portable Clamp-On Tub Seat SH-426
Measures 26.5" W x 15" D. Custom sizes available. 5 year warranty....
-
Bobrick Recessed Toilet Tissue Dispenser B-667
Single-roll model measure 6 1⁄8" W x 6 1⁄8" H (155 x 155mm)....
-
Access-Able Designs Shower Transfer Bench SH-400-2SDL
Measures 32" W x 15" D x 22.5" D. Complies w/ ADA 4.21.3 when properly installed 5 year warranty....
-
Bobrick Recessed Toilet Tissue Dispenser B-6677
Single-roll model measure 6 1⁄8" W x 6 1⁄8" H (155 x 155mm)....
-
302 Floor or Ground Surfaces
Historically, the Board has not specified a particular level of slip resistance since it can be measured in different ways....
-
11B-903.4 Back support
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADAS] 903.4 Back Support. ...
-
1117B.5.3
Characters on signs shall be selected from fonts that have a width-to-height ratio of between 3:5 (60 percent) and 1:1 (100 percent) measured by the width of the uppercase letter "O" and...
-
Transit Stops (R308.1) (Section-by-Section Analysis)
Transit Stops (R308.1) (Section-by-Section Analysis) Boarding and alighting areas at sidewalk or street level transit stops must be 2.4 meters (8 feet) minimum measured perpendicular...
-
Literature Review
The second topic was to explore ways to measure, design, and monitor the quality of pathway surfaces for WC users. Therefore two separate searches were conducted....
-
Accessible Pathway & Corridor: Minimum Clear Width Required for 180-degree Turn
Findings from the Anthropometry of Wheeled Mobility Study indicate that a width of at least 130 cm (51 in.) was required for 50% of the manual wheelchair users measured in this study to...
-
Accessible Pathway & Corridor: Minimum Clear Width Required for 180-degree Turn Around Barrier
Findings from the Anthropometry of Wheeled Mobility Study indicate that a uniform width of at least 89.5 cm (35 in.) was required for 50% of the manual and power wheelchair users measured...
-
1136A.1 Receptacle heights
Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located no more than 48 inches (1219 mm) measured from the top of the...
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”. ...
