The door maneuvering clearance must be measured from the leading edge of such elements so that the full clearance is free of any obstruction....
Search Results "Measuring Technique"
Filters
Commonly Searched Documents
-
Can handrails overlap door maneuvering clearances?
-
11B-603.6 Guest room toilet and bathing rooms
that are not required to provide mobility features complying with Section 11B-806.2 shall provide all toilet and bathing fixtures in a location that allows a person using a wheelchair measuring...
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
Portable Floor Lifts
To properly and safely assist patients with transfers, medical staff will likely need training on how to operate the equipment and on safe patient handling techniques....
-
Portable tactile maps
A number of techniques have been used to produce portable tactile maps, including vacuum forming three-dimensional shapes onto pre-printed vinyl sheets (e.g., the Lincoln Center map), embossing...
-
Tactile Design for Universal Access
Touch Graphics creates products and exhibits that rely on multi-sensory display techniques and audio-haptic interactivity....
-
1136A.1 Receptacle heights
Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located no more than 48 inches (1219 mm) measured from the top of the...
-
Accessible Ground Surfaces
This standard assesses the accessibility of a surface by measuring the work an individual must exert to propel a wheelchair across the surface....
-
R210.3 Shared Use Paths
Objects shall not overhang or protrude into any portion of a shared use path at or below 2.4 m (8.0 ft) measured from the finish surface....
-
Chapter M3 Technical Criteria
The technical criteria specify measurements in inches and millimeters....
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured between an entrance and all vehicular or pedestrian...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
1136A.1 Receptacle heights
Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located no more than 48 inches (1219 mm) measured from the top of the...
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
due to unusual characteristics of the site when: The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
11B-809.12 Electrical receptacles, controls and switches
circuits of 30 amperes or less, communication system receptacles, controls and switches shall be located as follows: Where there is no obstruction, 48 inches (1219 mm) maximum measured...
-
Appendix Two: Design Information and Accommodation Models
Research findings on Eye Height, measured on the right eye Type of WhMD user Sam-ple Size Mean (SD) Min 5%ile 10%ile Me-dian 90%ile...
-
2.4.1 Current Marketplace Dynamics
Notes I The methods for measuring “low heights” for current height adjustable products vary among manufacturers and product designs. No official measurement method currently exists....
-
Base Support [No specific provision—affects M303.2.4]
The footrest height data measures the height from the floor to the top surface of the footrest at its proximal outside corner....
-
A MINIMUM HIGHEST POINT STANDARD OF 19 INCHES IS CONSISTENT WITH EXISTING ACCESSIBILITY STANDARDS
The height of water closet seats shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the floor, measured to the top of the seat....
-
Seton Reserved Parking Sign (With Graphic) and Post
in aluminum, polyethylene and steel materials Non-reflective surface are best for day time use while reflective option allows the sign to be visible even at night Sign measures...
-
Gamco Horizontal Wall-Mounted Baby Changing Station Cream - BCS-1
Unit measures 35 1/4" W x 20" H (895 x 508mm). Depth (closed) 4" (100 mm). Extension (open) 19" (483mm)....
-
Gamco Horizontal Wall-Mounted Baby Changing Station Grey - BCS-2
Unit measures 35 1/4" W x 20" H (895 x 508mm). Depth (closed) 4" (100 mm). Extension (open) 19" (483mm)....
