Standards that measure a physical or mental ability needed to perform a job....
Search Results "Measuring Technique"
-
Evaluating Physical and Mental Qualification Standards Under the ADA
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
604.9.6 Dispensers
Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
-
404.2.4.3 Recessed Doors and Gates
clearances for forward approach shall be provided when any obstruction within 18 inches (455 mm) of the latch side of a doorway projects more than 8 inches (205 mm) beyond the face of the door, measured...
-
§ 36.303(c)(1)(ii)
should consult with individuals with disabilities whenever possible to determine what type of auxiliary aid is needed to ensure effective communication, but the ultimate decision as to what measures...
-
1134A.6, Item 1.2
1.2 The shower stall shall measure at least 30 inches deep by 60 inches wide (762 mm by 1524 mm) with an entrance opening of at least 60 inches (1524 mm)....
-
4.13.5 Clear Width
Doorways shall have a minimum clear opening of 32 in (815 mm) with the door open 90 degrees, measured between the face of the door and the opposite stop (see Fig. 24(a), (b), (c), and (d...
-
E102.8 Telecommunications Industry Association (TIA)
TIA 1083 defines measurement procedures and performance requirements for the handset generated audio band magnetic noise of wire line telephones, including digital cordless telephones....
-
III-9.8000 Certification and barrier removal in existing facilities
The Department will measure equivalency against subpart D of the title III rule, New Construction and Alterations....
-
Can handrails or other elements overlap door maneuvering clearances?
The door maneuvering clearance must be measured from the leading edge of such elements so that the full clearance is free of any obstruction....
-
Can handrails overlap door maneuvering clearances?
The door maneuvering clearance must be measured from the leading edge of such elements so that the full clearance is free of any obstruction....
-
11B-603.6 Guest room toilet and bathing rooms
that are not required to provide mobility features complying with Section 11B-806.2 shall provide all toilet and bathing fixtures in a location that allows a person using a wheelchair measuring...
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
1136A.1 Receptacle heights
Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located no more than 48 inches (1219 mm) measured from the top of the...
-
Accessible Ground Surfaces
This standard assesses the accessibility of a surface by measuring the work an individual must exert to propel a wheelchair across the surface....
-
R210.3 Shared Use Paths
Objects shall not overhang or protrude into any portion of a shared use path at or below 2.4 m (8.0 ft) measured from the finish surface....
-
Chapter M3 Technical Criteria
The technical criteria specify measurements in inches and millimeters....
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured between an entrance and all vehicular or pedestrian...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
1136A.1 Receptacle heights
Electrical receptacle outlets on branch circuits of 30 amperes or less and communication system receptacles shall be located no more than 48 inches (1219 mm) measured from the top of the...
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
due to unusual characteristics of the site when: The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured...
-
11B-809.12 Electrical receptacles, controls and switches
circuits of 30 amperes or less, communication system receptacles, controls and switches shall be located as follows: Where there is no obstruction, 48 inches (1219 mm) maximum measured...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...