The shoulder alignment point of the wheelchair space shall be measured 36 inches (914 mm) from the front of the wheelchair space....
Search Results "Measuring Technique"
Filters
Commonly Searched Documents
-
11B-802.3.1 Alignment
-
Designing Sidewalks and Trails for Access
Accessibility guidelines and practices, as well as construction and maintenance techniques, have evolved since these reports were published....
-
ADA+ Facilities Compliance Services
construction, facilities management and maintenance staff on ADA+ regulations, design standards and how to bring facilities into compliance Train ADA Coordinators on barrier management techniques...
-
Paragraph (i) (Advisory Guidance)
The following strategies are extensions of techniques for making products easier for everyone to learn and use: a....
-
The Smith-Kettlewell Eye Research Institute
in support of vision disorders, clinical research to develop new diagnostic procedures and treatments for visual and other sensory disorders, and engineering research to produce better techniques...
-
11B-605.2 Height and depth
Urinals shall be 13½ inches (343 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture. FIGURE 11B-605.2 HEIGHT AND DEPTH OF URINALS...
-
Sec.36.301(c) Charges
A public accommodation may not impose a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures, such as the provision...
-
Seat Height
Commenters noted that this specification should be clarified as applying to the height as measured at the top of the seat surface. Response....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
T404.3 Ramps and Bridgeplates
Where the space between the floor of non-rail vehicles and a boarding platform is greater than 2 inches (51 mm) horizontally or 5/8 inch (16 mm) vertically when measured at 50 percent passenger...
-
G. Compartment Size
If the accessible toilet is in a stall, does the stall measure at least 60" wide and 56" deep if it is wall mounted or 59" deep if it is floor mounted to allow persons who use wheelchairs...
-
§ 36.301(c) Charges
A public accommodation may not impose a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures, such as the provision...
-
4.7.2 Slope
The slope shall be measured as shown in Fig. 11. Transitions from ramps to walks, gutters, or streets shall be flush and free of abrupt changes....
-
Changes in Level - Accessible Route Tool
Changes in Level - Accessible Route Tool This handy tool was developed by Evan Terry Associates to assist its surveyors in measuring changes in level along an accessible route....
-
11B-608.2.3 Alternate roll-in type shower compartments
Alternate roll-in type shower compartments shall be 36 inches (914 mm) wide and 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
American Specialties Folding Shower Seat 8206-L
Seat measures 33" (840 mm) wide and projects 22 7/8" (580 mm) from wall....
-
605.2 Height and Depth
Urinals shall be 13½ inches (345 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture. Figure 605.2 Height and Depth of Urinals...
-
Sec.36.607(a)(2)
By the same token, certification would not be relevant to construction of a facility for children, if the regulations against which equivalency is measured do not address children's facilities...
-
605.2 Height and Depth
Urinals shall be 13½ inches (345 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture....
-
802.3.1 Alignment
The shoulder alignment point of the wheelchair space shall be measured 36 inches (915 mm) from the front of the wheelchair space....
-
11B-404.2.4.3 Recessed doors and gates
457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects more than 8 inches (203 mm) beyond the face of the door, measured...
-
11B-705.1.1.2 Dome spacing
detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (16.5 mm) minimum, measured...
-
11B-404.2.4.3 Recessed doors and gates
457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects more than 8 inches (203 mm) beyond the face of the door, measured...
-
DETR
., 2000) was limited to measurement of device size and weight....
