with official approval of recipient's management, any policies or practices that do not meet the requirements of this part according to a schedule or sequence that includes milestones or measures...
Search Results "Measuring Technique"
Filters
Commonly Searched Documents
-
§27.11(c)(2)(iii)
-
Clear Width [4.8.3]
The minimum dear width for ramps of 36 inches is measured between the leading edge of handrails. A maximum clear width is not specified....
-
Free-standing and Post-mounted Objects
This is based on standard measures for cane sweep. Objects with leading edges at or below 27 inches or above 80 inches can protrude any amount....
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
M301.4 Lift Compatibility
Compatibility M01.4.1 Clearance in Base Proposed requirement: The base of the equipment shall provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured...
-
A4.5.1 General
While the dynamic coefficient of friction during walking varies in a complex and non-uniform way, the static coefficient of friction, which can be measured in several ways, provides a close...
-
11B-705.1.1.2 Dome spacing
detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (16.5 mm) minimum, measured...
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions Measurement Range Minimum in Inches Maximum in Inches Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
§35.130(f) (Section-by-Section Analysis)
Paragraph (f) provides that a public entity may not place a surcharge on a particular individual with a disability, or any group of individuals with disabilities, to cover any costs of measures...
-
1017.5 Tread Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
Energy Consumption During Ambulation
Measurements were recorded for subjects walking on the Straight and Turning Courses....
-
11B-705.1.2.2.2.2 Two entrance/exit points
Where the turning space has two entrance/exit points other than the sloped ramp segments, detectable warnings shall be 36 inches (914 mm) deep at both entrance/ exit points, as measured...
-
1132A.3 Width and height of interior doors and secondary exterior doors
Swinging doors shall provide a net clear opening width of not less than 32 inches (813 mm), measured with the door or doors positioned at an angle of 90 degrees from the closed position....
-
M303.2.2 Width
EXCEPTION: Wheelchair spaces located on raised platforms shall be permitted to be 32 inches (815 mm) wide minimum to a height of 4 inches (100 mm) measured from the platform surface....
-
5.1.5 Floor Height
Where the floor at the entrance to the camp shelter is elevated above the ground surface, the floor shall be 17 (430 mm) high minimum to 19 inches (485 mm) high maximum measured from the...
-
2. b. i. Clear door openings
Clear openings of doorways with swinging doors shall be measured between the face of the door and the stop, with the door open 90° degrees.xiv...
-
Cross Slope
The percentage of rise to length, which is the difference in elevation, when measuring the trail tread from edge to edge perpendicular to the direction of travel This may be expressed as...
-
5.1.5 Floor Height
Where the floor at the entrance to the camp shelter is elevated above the ground surface, the floor shall be 17 (430 mm) high minimum to 19 inches (485 mm) high maximum measured from the...
-
Seton Pavement Tool Plastic Graphic Stencils - ISA Symbol (California DOT) S-3048 D - PP261
One-piece stencils are easy to align 1/16" thick plastic holds its shape use-after-use Dry paint flakes off the plastic for easy cleaning Stencils easily roll up for storage Stencil measures...
-
American Specialties Compact Rectangular Phenolic Fold-Up Shower Seat 8203
mm) thick, one piece, solid phenolic, ivory colored Frame, support legs, flanges and bracket are type 304 satin finished stainless steel Features a self-locking mechanism Seat measures...
-
Seton Pavement Tool Plastic Graphic Stencils - ISA Symbol (Texas DOT) S-3148 D - PP262
Stencils easily roll up for storage Stencil measures 41-1/4"W x 4" Bar x 48"H with ISA symbol Meets Texas DOT specs One-piece stencils are easy to...
-
Seton Directional Entrance Sign - Left Arrow
Engineer Grade reflective .063" aluminum material is equally visible day or night Extend the life and performance of your sign by upgrading to Seton UltraTuff™ overlaminate Signs measure...
-
Seton Optima Men Restroom Sign
resistant finish with raised white Optima font letters and numbers Grade 2 Braille complies with Federal and California specifications Easily mounted with adhesive strips included Signs measure...
-
Tips for riding the Freedom Chair
You'll learn how to use the levers for propulsion a special technique for climbing steep hills....
