Clearance in front of bathtubs shall extend the length of the bathtub and shall be 48 inches (1219 mm) wide minimum for forward approach and 30 inches (762 mm) wide minimum for parallel...
Search Results "Counter Length"
-
11B-607.2 Clearance
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
§ 38.23(d)(4) Orientation
In vehicles in excess of 22 feet in length, at least one securement device or system required by paragraph (a) of this section shall secure the wheelchair or mobility aid facing toward the...
-
11B-607.2 Clearance
Clearance in front of bathtubs shall extend the length of the bathtub and shall be 48 inches (1219 mm) wide minimum for forward approach and 30 inches (762 mm) wide minimum for parallel...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
Step 3: Apply the Accessibility Provisions
If the grade requirement can't be met because of a condition for an exception, measure and record the length of trail that will deviate from the technical requirement....
-
1.1.13 Flatness of ramp running slope
Measure flatness in the running slope of ramps at 12 - in. (300 mm) increments by using successive, overlapping 24 - in. (600 mm) lengths using a 24 - in. digital inclinometer....
-
M303.2.3 Wheelchair Spaces / Depth of Wheelchair Spaces for front or Rear Entry
• Sub-Committee Recommendation: Platform size shall be clear width of 32 inches minimum and clear length of 40 inches minimum....
-
FBD Partnership Four Flavors Frozen Beverage Dispenser
RapidFreeze™ Cold Chamber system improves recovery and draw-time, while reducing compressor run-time Electronic Simplicity offers easy-to-use keypad interface Optimal Use of Counter...
-
Just Manufacturing Ledgemount Non-Swivel Gooseneck Concealed Mixing Faucet
Deck mount faucet - Lead Free Compliant - Concealed body mounts below counter surface - Rigid non-swiveling gooseneck spout - 1.5 GPM flow restricting aerator....
-
4.16.4 Grab Bars
Among the various specifications for grab bars in general, including diameter, spacing, and structural strength (ADAAG 4.26) and for toilets in particular, including length and positioning...
-
M305.3.2 Vertical Position
Where the support is vertical, it shall be 18 inches (455 mm) minimum in length and the bottom end of the support shall be 34 inches (865 mm) high minimum and 37 inches (940 mm) high maximum...
-
A. Door Width
on an over-the-road bus is considered not feasible if doing so would necessitate reduction of the bus approach angle, relocating the front axle rearward, or increasing the bus overall length...
-
Pilot Rock Sign Benches
A variety of lengths, colors and materials to give you the look you want....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
2. a. iii. Costs
Doors at entrances, Accessible door hardware, Adequate wheelchair maneuvering space, Accessible fixed seating and tables, and Accessible sales and service counters...
-
4.34.6.10* KITCHEN STORAGE
shall comply with 4.25 and shall have the following features: (1) Maximum height shall be 48 in (1220 mm) for at least one shelf of all cabinets and storage shelves mounted above work counters...
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
Dining Surface and Work Surface
Some commenters considered the term too limiting and questioned whether it would apply, as they felt it should, to surfaces used forpurposes not necessarily considered "work," such as counters...
-
1017.10 Trailhead Signs
Length of the trail or trail segment; 2. Surface type; 3. Typical and minimum tread width; 4. Typical and maximum running slope; and 5....
-
407.8.3.2 Obstructed Forward Reach
Where the operable part is located beyond the leading edge of the maximum protrusion within the length of the vertical reference plane, the operable part shall conform to 407.8.3.2....
-
G1
Yes No Note: it may narrow to 32 inches wide for up to 2 feet in length. [ADA Standards § 4.3.2(3)]...
-
K1
accessible route, at least 36 inches wide, that connects each of the shelter activity areas with the food service and eating areas (it may narrow to 32 inches wide for up to 2 feet in length...
