shall comply with 4.25 and shall have the following features: (1) Maximum height shall be 48 in (1220 mm) for at least one shelf of all cabinets and storage shelves mounted above work counters...
Search Results "Counter Length"
Filters
Commonly Searched Documents
-
4.34.6.10* KITCHEN STORAGE
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware....
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
4.16.4 Grab Bars
Among the various specifications for grab bars in general, including diameter, spacing, and structural strength (ADAAG 4.26) and for toilets in particular, including length and positioning...
-
M305.3.2 Vertical Position
Where the support is vertical, it shall be 18 inches (455 mm) minimum in length and the bottom end of the support shall be 34 inches (865 mm) high minimum and 37 inches (940 mm) high maximum...
-
A. Door Width
on an over-the-road bus is considered not feasible if doing so would necessitate reduction of the bus approach angle, relocating the front axle rearward, or increasing the bus overall length...
-
4.3.3 Clear Floor Area
The 95th percentile dimension values for occupied length and breadth provide a reasonable threshold value for determining the dimensions for clear floor area length and breadth....
-
5.8.1.1 Clear Platform Size Recommendation
5.8.1.1 Clear Platform Size Recommendation The Committee recommends a platform size with a minimum clear width of 32 inches and a minimum clear length of 40 inches....
-
1017.10 Trailhead Signs
Length of the trail or trail segment; 2. Surface type; 3. Typical and minimum tread width; 4. Typical and maximum running slope; and 5....
-
407.8.3.2 Obstructed Forward Reach
Where the operable part is located beyond the leading edge of the maximum protrusion within the length of the vertical reference plane, the operable part shall conform to 407.8.3.2....
-
G1
Yes No Note: it may narrow to 32 inches wide for up to 2 feet in length. [ADA Standards § 4.3.2(3)]...
-
K1
accessible route, at least 36 inches wide, that connects each of the shelter activity areas with the food service and eating areas (it may narrow to 32 inches wide for up to 2 feet in length...
-
10.3.1(8)
Such detectable warnings shall comply with 4.29.2 and shall be 24 inches wide running the full length of the platform drop-off....
-
1017.10 Trailhead Signs
Length of the trail or trail segment; 2. Surface type; 3. Typical and minimum tread width; 4. Typical and maximum running slope; and 5. Typical and maximum cross slope....
-
FBD Partnership Four Flavors Frozen Beverage Dispenser
RapidFreeze™ Cold Chamber system improves recovery and draw-time, while reducing compressor run-time Electronic Simplicity offers easy-to-use keypad interface Optimal Use of Counter...
-
Just Manufacturing Ledgemount Non-Swivel Gooseneck Concealed Mixing Faucet
Deck mount faucet - Lead Free Compliant - Concealed body mounts below counter surface - Rigid non-swiveling gooseneck spout - 1.5 GPM flow restricting aerator....
-
Pilot Rock Sign Benches
A variety of lengths, colors and materials to give you the look you want....
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
5.9.2.2 Standing Supports on Dual Ramped Entry Raised Platforms with Wheelchair Spaces
Standing supports should be located on one side of the platform, integrated into the platform and stretching the full length of the platform (40 inch minimum) for dual ramped entry raised...
-
R308.1.1.1 Dimensions
Boarding and alighting areas shall provide a clear length of 2.4 m (8.0 ft) minimum, measured perpendicular to the curb or street or highway edge, and a clear width of 1.5 m (5.0 ft) minimum...
-
407.8.3.1 Unobstructed Forward Reach
Where the operable part is located at the leading edge of the maximum protrusion within the length of the vertical reference plane of the ICT, the operable part shall be 48 inches (1220...
-
2. Using the Tape Measure
Using the Tape Measure A metal tape measure is needed to measure the length, width, height, and depth of various elements....
-
N1
accessible route, at least 36 inches wide, that connects each of the shelter activity areas with the health units and medical care areas (it may narrow to 32 inches wide for up to 2 feet in length...
-
§ 38.35(a)
(a) Vehicles in excess of 22 feet in length, used in multiple-stop, fixed-route service, shall be equipped with a public address system permitting the driver, or recorded or digitized human...
