Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
Search Results "Counter Length"
-
505.6 Gripping Surface
-
11B-505.6 Gripping surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
11B-221.2.3.1 Horizontal dispersion
required in assembly areas with 300 or fewer seats if the companion seats required by Section 11B-221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
11B-221.2.3.1 Horizontal dispersion
required in assembly areas with 300 or fewer seats if the companion seats required by Section 11B-221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
11B-306.3.3 Minimum required depth
high minimum above the finish floor or ground at a depth of 8 inches (203 mm) minimum increasing to 29 inches (737 mm) high minimum above the finish floor or ground at the front edge of a counter...
-
11B-306.3.3 Minimum required depth
high minimum above the finish floor or ground at a depth of 8 inches (203 mm) minimum increasing to 29 inches (737 mm) high minimum above the finish floor or ground at the front edge of a counter...
-
§ 36.309(b)(2)
(2) Required modifications to an examination may include changes in the length of time permitted for completion of the examination and adaptation of the manner in which the examination is...
-
Sec.36.309(b)(2)
(2) Required modifications to an examination may include changes in the length of time permitted for completion of the examination and adaptation of the manner in which the examination is...
-
1016.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1016.7.1) and cross slope (1016.7.2) of outdoor recreation access routes....
-
Boarding Piers at Boat Launch Ramps: ADA Standard Section 1003.2.2
Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2...
-
11B-502.6.4.2
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
11B-502.6.4.2
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
11B-805.4.3 Turning space
Refer to the following examples: Exam room - Exam rooms are required to provide a turning space, accessible handwashing fixture, and 36-inch wide access along the full length of each...
-
11B-805.4.3 Turning space
Refer to the following examples: Exam room - Exam rooms are required to provide a turning space, accessible handwashing fixture, and 36-inch wide access along the full length of each...
-
11B-406.5.3 Landings
The landing clear length shall be 48 inches (1219 mm) minimum....
-
11B-406.5.3 Landings
The landing clear length shall be 48 inches (1219 mm) minimum....
-
§382.133(e)(2)
(2) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with FAA safety requirements...
-
§ 38.29(c)
(c) For vehicles in excess of 22 feet in length, overhead handrail(s) shall be provided which shall be continuous except for a gap at the rear doorway....
-
Boarding Pier Clearances
Boarding Pier Clearances The entire length of accessible boarding piers must comply with the same technical provisions that apply to boat slips....
-
Unified Facilities Guide Specifications
The straightedge is to be held in contact with the surface and moved ahead one - half of the length of the straightedge for each successive measurement....
-
Food Service Lines [5.5] and Tableware and Condiment Areas [5.6]
Pass-through space at service counters can provide easier access....
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....