Access aisle markings may extend beyond the minimum required length....
Search Results "Counter Length"
Filters
Commonly Searched Documents
-
11B-812.7.2 Marking
-
Selection of Variables
Selection of Variables Our own review of the ADAAG requirements, plus that of our subcontractor KRW, reveals that the single most needed anthropometric datum, by far, is arm length....
-
9.6 ATTENDANCE-RECORDING EQUIPMENT
Counter space at check-in areas must be no more than 36 in (915 mm) above the finished floor....
-
T402.5 Surfaces
Ramp and bridgeplate surface material shall comply with T302 and extend across the full width and length of the ramp or bridgeplate....
-
1017.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1017.7.1) and cross slope (1017.7.2) of trails....
-
New Construction and Alterations
If you build a new facility or modify your existing one, (for example, work such as restriping the parking area, replacing the entry door or renovating the sales counter), make sure to consult...
-
11B-805.4.3 Turning space
Refer to the following examples: Exam room - Exam rooms are required to provide a turning space, accessible handwashing fixture, and 36-inch wide access along the full length of each...
-
11B-805.4.3 Turning space
Refer to the following examples: Exam room - Exam rooms are required to provide a turning space, accessible handwashing fixture, and 36-inch wide access along the full length of each...
-
Common Use Circulation Paths in Employee Work Areas [§206.2.8]
Paths in Employee Work Areas [§206.2.8] Common use circulation paths must be accessible in work areas 1,000 square feet or more in size (as defined by permanently installed partitions, counters...
-
11B-306.3.3 Minimum required depth
high minimum above the finish floor or ground at a depth of 8 inches (203 mm) minimum increasing to 29 inches (737 mm) high minimum above the finish floor or ground at the front edge of a counter...
-
Side Transfer Surface
A transfer surface located within the length of the examination surface that allows patient transfer on two opposing sides of the examination surface....
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side....
-
6.8.1 Size
The resting interval length shall be a minimum of 60 inches (1525 mm) long by 60 inches (1525 mm) wide....
-
11B-221.2.3.1 Horizontal dispersion
required in assembly areas with 300 or fewer seats if the companion seats required by Section 11B-221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
11B-505.6 Gripping surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
11B-221.2.3.1 Horizontal dispersion
required in assembly areas with 300 or fewer seats if the companion seats required by Section 11B-221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
11B-221.2.3.1 Horizontal dispersion
required in assembly areas with 300 or fewer seats if the companion seats required by Section 11B-221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
-
11B-406.5.3 Landings
The landing clear length shall be 48 inches (1219 mm) minimum....
-
5.8.1.1 Clear Platform Size
The platform should be a minimum clear width of 32-inches and a minimum clear length of 40-inches....
-
1018.7 Slopes
This section contains technical requirements for the maximum running slope and segment length (1018.7.1) and cross slope (1018.7.2) of beach access routes....
-
Boarding Piers at Boat Launch Ramps: ADA Standard Section 1003.2.2
Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9145 mm) minimum, gangways shall not be required to comply with 405.2...
-
11B-502.6.4.2
The centerline of the International Symbol of Accessibility shall be a maximum of 6 inches (152 mm) from the centerline of the parking space, its sides parallel to the length of the parking...
-
§ 36.309(b)(2)
(2) Required modifications to an examination may include changes in the length of time permitted for completion of the examination and adaptation of the manner in which the examination is...