Some accessible tables must be provided and must be dispersed throughout the dining area rather than clustered in a single location....
Search Results "Horizontal Dispersion"
-
Food and Restaurant Services
-
Guest Rooms with Communication Features
Commenters suggested that the requirements for scoping and dispersion of guest rooms for persons with mobility impairments and guest rooms with communication features are too complex for...
-
20. DESIGN AND CONSTRUCTION STANDARDS
for review and approval a web-based design guide that identifies the ADA Standards requirements for: (1) registration and other service counters; (2) accessible guest room numbers and dispersion...
-
11B-405.9 Edge protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (12.7 mm) maximum within 10 inches (254 mm) horizontally of the minimum landing area...
-
1007.6 Areas of refuge
elevator lobby is used as an area of refuge, the shaft and lobby shall comply with Section 1022.10 for smokeproof enclosures except where the elevators are in an area of refuge formed by a horizontal...
-
Issue 9: Reach (how far?)
APS should be within the reach range (1.2 m/48 inches vertically, .25m/10 inches horizontally) for an individual who uses a wheelchair (draft PROWAG, R404)....
-
M305.3.2 Height (Section-by-Section Analysis)
For horizontal supports, the MDE NPRM proposed a gripping surface height of 34 inches minimum and 38 inches maximum above the standing surface....
-
M304.2.2 Standing Supports (Section-by-Section Analysis)
equipment with entry and exit that permits pass-through from one end to another to provide one standing support provided it complies with the requirements for standing supports in the horizontal...
-
Handrails
Where provided, horizontal projections shall occur 1 1/2 inches (38 mm) minimum below the bottom of the handrail gripping surface....
-
608.3 Grab Bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor. EXCEPTIONS: 1....
-
608.3 Grab Bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor. EXCEPTIONS: 1....
-
Grade (R302.5) (Section-by-Section Analysis)
Grade is calculated by dividing the vertical change in elevation by the horizontal distance covered, and is expressed as a percent....
-
1.1.12 Ramp cross slope
overall cross slope of ramps by establishing elevations at the extreme edges of the ramp at the top and bottom of the ramp and calculate the cross slope at these two locations using the horizontal...
-
Stairs
At the bottom, the handrail shall continue to slope for a distance of the width of one tread from the bottom riser; the remainder of the extension shall be horizontal (see Fig. 19(c) and...
-
11B-405.9 Edge protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (12.7 mm) maximum within 10 inches (254 mm) horizontally of the minimum landing area...
-
1009.7.2 Separation
The fire-resistance-rated exterior wall construction shall extend horizontally 10 feet (3048 mm) beyond the landing on either side of the landing or equivalent fire-resistance-rated construction...
-
1009.3.3 Area of Refuge
Areas of refuge are not required for stairways accessed from a refuge area in conjunction with a horizontal exit....
-
11B-405.9 Edge protection
Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of ½ inch (12.7 mm) maximum within 10 inches (254 mm) horizontally of the minimum landing area...
-
703.5.5 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
M305.3 Standing Supports (Section-by-Section Analysis)
This provision has been reorganized in the final rule into requirements for length and height, as opposed to vertical and horizontal....
-
703.5.5 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
703.5.5 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
703.5.5 Character Height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....