Where provided, horizontal projections shall occur 1 1/2 inches (38 mm) minimum below the bottom of the handrail gripping surface. EXCEPTIONS: 1....
Search Results "Minimum Dimension"
-
505.6 Gripping Surface
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADAS] 405.7.5 Doorways....
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
11B-703.7.2.1 International Symbol of Accessibility
A border may be provided inside or outside of the minimum required International Symbol of Accessibility dimension....
-
308.1 General
These dimensions apply to either forward or side reaches....
-
308.1 General
These dimensions apply to either forward or side reaches....
-
§ 36.311(b)(2)(i)
(i) The type, size, weight, dimensions, and speed of the device;...
-
§ 35.137(b)(2)(i)
(i) The type, size, weight, dimensions, and speed of the device;...
-
Re: Lavatories Adjacent to Partitions
The question is where is the location of dispenser/element in question. 11B-606.6 requires lavatories adjacent to sidewall or partition to be a minimum of 18" to the centerline of the...
-
Transfer Surface Height (M301.2.1 and M302.2.1)
M301.2.1 and M302.2.1 would require the height of the transfer surface during patient transfer to be 17 inches minimum and 19 inches maximum measured from the floor to the top of the transfer...
-
Section 4.26.2
Handrail gripping surfaces with a non-circular cross section must have a perimeter dimension of 4 inches to 6 ¼ inches, and a cross section dimension of 2 ¼ inches maximum....
-
R103 Conventions (Section-by-Section Analysis)
R103 Conventions (Section-by-Section Analysis) Conventional industry tolerances apply where dimensions are not stated as a range....
-
§ 36.311(c)(1)
(1) The dimensions, weight, and operating speed of the mobility device in relation to a wheelchair;...
-
§ 35.137(c)(1)
(1) The dimensions, weight, and operating speed of the mobility device in relation to a wheelchair;...
-
3.2 Dimensional Tolerances
All dimensions are subject to conventional building industry tolerances for field conditions....
-
3.2 DIMENSIONAL TOLERANCES
All dimensions are subject to conventional building industry tolerances for field conditions....
-
Verify Framing
bars in bathtub/shower rooms. 11B-610 Width and depth of shower stalls. 11B-608.2 Drinking fountain alcoves/wing walls. 11B-602.9 Tread dimensions...
-
Verify Framing
bars in bathtub/shower rooms. 11B-610 Width and depth of shower stalls. 11B-608.2 Drinking fountain alcoves/wing walls. 11B-602.9 Tread dimensions...
-
Data Analysis
The 5th, 25th, 50th, 75th, and 95th percentiles were recorded along with the minimum and maximum heights attained for each part of each protocol....
-
T210 Wheelchair Spaces
A van manufacturer suggested, in response to the 2010 NPRM, that the Access Board add language in the final rule that would allow additional spaces, even if they do not meet the minimum...
-
Parking sign height measurement technique
502.6 says "Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign." But which floor or ground surface? ...
-
Single-User Toilet Rooms: Side Transfer Space
Knee and toe clearances below fixtures can overlap turning space, although this should be limited where the space is confined to the minimum (see page 15)....
-
304 Turning Space
The Department recognizes that the technical specifications for T-shaped and circular turning spaces in the 1991 and 2010 Standards, which are based on manual wheelchair dimensions, may...