Pictograms shall have a field height of 6 inches (152 mm) minimum. Characters and Braille shall not be located in the pictogram field. Advisory 11B-703.6.1 Pictogram field. ...
Search Results "Minimum Dimension"
-
11B-703.6.1 Pictogram field
-
5.4.2.1 Transfer Support Length Recommendation for Stretchers
5.4.2.1 Transfer Support Length Recommendation for Stretchers On Stretchers, the transfer surface is oriented along the long dimension of the surface on which patients are positioned...
-
Doorways [4.8.4]
Keeping the door swing clear of minimum landing dimensions is a good idea, especially at the bottom of ramps since people using wheelchairs may exit them with some force and speed....
-
5.2.1.2 Transfer Surface Depth Recommendation for M301
The Committee easily supported this increase as existing equipment already encompassed this dimension. The Committee reviewed anthropometric data from a variety of sources. Dr....
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
407.12.3.1 Unobstructed Forward Reach (Section-by-Section Analysis)
Section-by-Section Analysis) This section proposes that, where an unobstructed forward reach is provided, the operable part must be located 48 inches high maximum and 15 inches high minimum...
-
4.10.3 Hall Call Buttons
Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top. (See Fig. 20.) Buttons shall be raised or flush....
-
4.10.3 HALL CALL BUTTONS
Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top (see Fig. 20). Buttons shall be raised or flush....
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
Alterations [4.1.6(1)(f) & (k)]
For example, if the planned scope of work is limited to replacement of an elevator cab's control panel, then at a minimum the new control panel must comply to the maximum extent feasible...
-
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis)
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis) This section would provide that dimensions are subject to conventional industry tolerances except where dimensions...
-
Seat width and depth
Additionally a 30 inch minimum width has been proposed medical diagnostic exam tables. ...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
Parallel Grab Bars
In finalizing this rule, the Board has sought to specify dimensions as a range instead of in absolute terms where possible to facilitate compliance without compromising accessibility....
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-405.7.2.1
Top landings shall be 60 inches (1524 mm) wide minimum. Advisory 11B-405.7.2.1 Top landing width....
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
Calculation of Percentages: ADA Standard Section 104.2
Section 104.2 of the ADA Standards covers the most current information on the calculation of percentages in the ADA Standards.
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
604.2 Location
The centerline of the water closet shall be 16 inches (405 mm) minimum to 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430...
-
11B-604.9 Water closets and toilet compartments for children's use
When the exception in Section 11B-604.1 is used, the suggested dimensions of Table 11B-604.9 for a single age group shall be applied consistently to the installation of a water closet and...
-
11B-604.9 Water closets and toilet compartments for children's use
When the exception in Section 11B-604.1 is used, the suggested dimensions of Table 11B-604.9 for a single age group shall be applied consistently to the installation of a water closet and...
-
C101.3 Conventional Industry Tolerances (Section-by-Section Analysis)
C101.3 Conventional Industry Tolerances (Section-by-Section Analysis) This proposed section, which has a parallel provision in the proposed 508 Standards (E101.3), would provide that dimensions...