Call buttons shall be a minimum of 3/4 in (19 mm) in the smallest dimension. The button designating the up direction shall be on top (see Fig. 20). Buttons shall be raised or flush....
Search Results "Minimum Dimension"
Filters
Commonly Searched Documents
-
4.10.3 HALL CALL BUTTONS
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
Grohe America Allure Brilliant Faucet
Complex without being complicated, faceted faucets add a new dimension to bathroom design, and a new dimension to water....
-
Seat width and depth
Additionally a 30 inch minimum width has been proposed medical diagnostic exam tables. ...
-
604.2 Location
The centerline of the water closet shall be 16 inches (405 mm) minimum to 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430...
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
Parallel Grab Bars
In finalizing this rule, the Board has sought to specify dimensions as a range instead of in absolute terms where possible to facilitate compliance without compromising accessibility....
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-405.7.2.1
Top landings shall be 60 inches (1524 mm) wide minimum. Advisory 11B-405.7.2.1 Top landing width....
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADA Standards] 405.7.5 Doorways....
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
M303.2.3 Wheelchair Spaces / Depth of Wheelchair Spaces for front or Rear Entry
Based on recent anthropometric data, NPRM proposes to increase minimum depth dimension from 48 to 58 inches – majority of members have no opinion or anticipation of a situation where requirement...
-
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis)
E101.3 Conventional Industry Tolerances (Section-by-Section Analysis) This section would provide that dimensions are subject to conventional industry tolerances except where dimensions...
-
2. REGULATORY BUILT-IN TOLERANCES
REGULATORY BUILT-IN TOLERANCES: California Building Code Section 1101B.5 indicates all dimensions are subject to conventional industry tolerances except where the requirement is stated as...
-
B. Restrooms
These specifications are derived from requirements for rail vehicles and represent compromises between space needed for use and constraints imposed by vehicle dimensions....
-
11B-604.9 Water closets and toilet compartments for children's use
When the exception in Section 11B-604.1 is used, the suggested dimensions of Table 11B-604.9 for a single age group shall be applied consistently to the installation of a water closet and...
-
11B-903.4 Back support
The bench shall provide for back support or shall be affixed to a wall along its long dimension....
-
11B-903.4 Back support
The bench shall provide for back support or shall be affixed to a wall along its long dimension....
-
Calculation of Percentages: ADA Standard Section 104.2
Section 104.2 of the ADA Standards covers the most current information on the calculation of percentages in the ADA Standards.
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment On imaging equipment, the transfer surface is oriented along the long dimension of the surface where...
-
Clear Floor Space [4.35.2]
Recommendations: Consider additional space on the narrow dimension to allow alternative transfers. Some people may need to fully recline to dress or change clothes....
