Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range. Advisory R103.1 Conventional Industry Tolerances....
Search Results "Minimum Dimension"
-
R103.1 Conventional Industry Tolerances
-
Re: Angled Parking
Requires the Accessibility Specialist plan or above. (Login or upgrade your account!)
-
1. Abdomen depth (AD)
dimensions are unrestricted or unbounded....
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and that the lift platform accommodate a wheelchair measuring 30 inches by 48 inches....
-
Is a transportation operator required to procure vehicles with lifts that have a design load of more than 600 pounds?
No. 49 CFR Part 38 continues to require that lifts have a minimum design load of 600 pounds and that the lift platform accommodate a wheelchair measuring 30 inches by 48 inches....
-
11B-703.4.2 Location
Signs containing tactile characters shall be located so that a clear floor space of 18 inches (457 mm) minimum by 18 inches (457 mm) minimum, centered on the tactile characters, is provided...
-
11B-703.4.2 Location
Signs containing tactile characters shall be located so that a clear floor space of 18 inches (457 mm) minimum by 18 inches (457 mm) minimum, centered on the tactile characters, is provided...
-
e-ii
[ADA Standards § 4.10.9, Fig. 22] Yes No Note: See Figure 22 for acceptable floor and opening dimensions....
-
4.1.6(3)(c)(iii)
(iii) Equivalent facilitation may be provided with an elevator car of different dimensions when usability can be demonstrated and when all other elements required to be accessible comply...
-
5b.
[ADA Stds 4.10.9] Note: See Figure 22 for acceptable floor and opening dimensions....
-
Truncated Domes
In the final rule, the Board has revised the specification for the diameter and spacing of truncated domes to permit a range of dimensions (705.1.1)....
-
11B-302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel. Advisory 11B-302.3 Openings....
-
M302.2.3 Size (Section-by-Section Analysis)
increased to 17 inches, a disability advocate recommended increasing the width to 23 inches, two of the commenters, accessibility consultant and disability advocate, stated that the proposed dimensions...
-
Landscape Forms Inc. Max Transportation Stop Shelters
A trellis supported by strong, slim legs it defines space in three dimensions and creates focal points in the urban landscape....
-
Wheelbase Definition
The larger of the dimensions measured on the right and left side of the mobility device were considered for the analysis....
-
Self Contained, Closed Products - Side Reach Range
Requires the Accessibility Specialist plan or above. (Login or upgrade your account!)
-
Wall furr-out to support a grab bar when toilet is too far from the side wall
It's like what Daniel is describing but I'm not sure about the exact dimensions or construction details of the one in these photos....
-
5.4.2.2 Transfer and Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces
Positioning Support Length Recommendations for Imaging Equipment with Transfer Surfaces On imaging equipment with transfer surfaces, the transfer surface is oriented along the long dimension...
-
Re: Section 307 Protruding Objects
The more blatant inconsistency is the lavatory, which is required to be 17" deep minimum due to the required forward approach clear floor/knee and toe space, and must provide knee clearance...
-
308.1 General
These dimensions apply to either forward or side reaches....
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADAS] 405.7.5 Doorways. ...
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
Platform Edges
This depth is an absolute dimension, not a minimum. Some platforms are edged with a buffer material that is designed to break away if hit by cargo trains....
-
Space Allowance and Reach Ranges [4.2]
Adult dimensions and measures for standard manual wheelchairs form the basis of many ADAAG specifications....
