Conclusions Design criteria based on the univariate analysis of abdomen depth is sufficient if all other clearance dimensions are unbounded (i.e., unrestricted) and abdomen depth is the...
Search Results "Minimum Dimension"
-
Conclusions
-
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302
The transfer surface dimensions do not include headrests, footrests, or similar supports for body extremities that do not support the patient’s overall body position....
-
407.12.3.2 Obstructed Forward Reach (Section-by-Section Analysis)
In addition, this proposed section also contains subsections, as discussed below, establishing maximum heights for operable parts with obstructed forward reaches, as well as dimensions for...
-
M301.2.2 Transfer Surface Size
The minimum size of the transfer surface is 28 inches wide minimum and 21 inches deep minimum and is located such that the long dimension of 28 inches is be located parallel to the patient...
-
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301)
5.2.1.4 Transfer Surface Size Recommendations for Imaging Equipment (M301) The Committee recommends a transfer surface size on imaging equipment be a minimum of 28 inches long by a minimum...
-
5.8.2.8 Knee and Toe Clearance Recommendations Summary
For such a measurement, the top of the breast platform will be moved to 34 inches above the ground, and then the clearance dimensions will be measured just as they would be on any stationary...
-
Parking
PARKING Location and number of van parking and standard parking spaces. 11B-208 Dimensions of accessible parking spaces and access...
-
Parking
PARKING Location and number of van parking and standard parking spaces. 11B-208 Dimensions of accessible parking spaces and access...
-
T-turn Maneuvering Space
The Department has decided to delete the reference to the T-turn dimensions in the Guidelines for Requirement 4....
-
Size and Spacing of Grab Bars and Handrails [4.26.2]
The 1½ inch clearance between walls and handrails or grab bars is an absolute dimension; it provides knuckle clearance while generally disallowing entrapment of the forearm or elbow....
-
Alterations: Alternate Stalls
Wheelchair maneuvering and transfer can be very difficult or impossible within these dimensions which is why these designs are permitted only in alterations where "technical infeasibility...
-
11B-505.6 Gripping surface
Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface....
-
Technical requirements
Technical requirements state the specific numbers, conditions, and measurements that are required (percent that must comply, dimensions, reach ranges, grades, trail width, and so forth)....
-
§ 38.4(b) Dimensional tolerances
All dimensions are subject to conventional engineering tolerances for material properties and field conditions, including normal anticipated wear not exceeding accepted industry-wide standards...
-
11B-1008.4.2 Clear floor or ground space
These dimensions apply to either forward or side reaches. The reach ranges are appropriate for use with those play components that children seated in wheelchairs may access and reach....
-
11B-812.10.4 Location
Where the long dimension of a vehicle space is parallel to the vehicular way, the EV charger shall be adjacent to, and 48 inches (1219 mm) maximum from the head end or foot end of the vehicle...
-
11B-812.10.4 Location
Where the long dimension of a vehicle space is parallel to the vehicular way, the EV charger shall be adjacent to, and 48 inches (1219 mm) maximum from the head end or foot end of the vehicle...
-
Elongated surface openings must be perpendicular to the dominant direction of travel, but what if there is no dominant direction of travel?
When there is no dominant direction of cross traffic, openings must be limited to ½” in both dimensions. ...
-
M101.6 Dimensional Tolerances (Section-by-Section Analysis)
The MDE NPRM proposed that dimensions were to be subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions....
-
Re: 405 Ramps
A ramp with a direction change requires a 60" x 60" minimum intermediate landing, which isn't just a turning space but also a place for stopping to allow for a turn....
-
Accessible Passenger Loading Zones [§503]
Accessible Passenger Loading Zones [§503] Requirements for accessible passenger loading zones address vehicle pull-up spaces and access aisles, including their dimensions, surfacing,...