Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
Search Results "Minimum Dimension"
-
1011.2.4 Openings
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
11B-104.2 Calculation of percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half shall be permitted....
-
11B-604.9 Water closets and toilet compartments for children's use
When the exception in Section 11B-604.1 is used, the suggested dimensions of Table 11B-604.9 for a single age group shall be applied consistently to the installation of a water closet and...
-
11B-604.9 Water closets and toilet compartments for children's use
When the exception in Section 11B-604.1 is used, the suggested dimensions of Table 11B-604.9 for a single age group shall be applied consistently to the installation of a water closet and...
-
Introduction
Dimension definitions and measurement techniques vary from study to study and, in many cases, samples were very small....
-
1115B.4.4.8, Item 1
A folding seat mounted 18 inches (457 mm) above the floor, and with a minimum space of 1 inch (25 mm) and maximum space of 1 1/2 inches (38 mm) allowed between the edge of the seat and any...
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADA Standards] 405.7.5 Doorways....
-
A. Slope at Door
If a fully automatic door is not provided, is the walkway in front of the lobby door level, without any portion steeper than 1:50 (critical dimension of ´" or less), so persons who use wheelchairs...
-
R305.2 Placement
Where the back of curb edge is tooled to provide a radius, the border dimension should be measured from the end of the radius....
-
R103.2 Calculation of Percentages
Where the determination of the required size or dimension of an element or facility involves ratios or percentages, rounding down for values less than one half is permitted....
-
Controls [4.21.5]
The dimensions for seats in 36 inch stalls are appropriate for seats in roll-in showers as well....
-
§ 38.23(b)(2)(ii) Exception
Where the lift is designed to deploy with its long dimension parallel to the vehicle axis and which pivots into or out of the vehicle while occupied (i.e., “rotary lift”), the requirements...
-
Parking sign height measurement technique
502.6 says "Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign." But which floor or ground surface? ...
-
2. Analysis of footrest clearance height and depth
The range and median values measured on the right-side for these three dimensions are presented in table 2. Critical values are highlighted in yellow....
-
SafePath: ADA Entry Level Landing Installation Training Video
requires more than just a ramp, it requires a level-landing, otherwise known as maneuverable clearance area, a firm and stable level surface area in front of the door designed to specific dimensions...
-
Water Closet Clear Floor Space in Toilet Compartments
The Board has not revised the minimum dimensions for the clear floor space at water closets....
-
Can parking signage height be considered a "safe harbor"?
No specific height dimension given. For an older property with parking signs mounted at, say 45" inches to the bottom, are these protected by the safe harbor rule? ...
-
1011.2.4 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
4.10.9 Floor Plan of Elevator Cars
Acceptable door opening and inside dimensions shall be as shown in Fig. 22....
-
4.10.9 FLOOR PLAN OF ELEVATOR CARS
Acceptable door opening and inside dimensions shall be as shown in Fig. 22....
-
1011.2.4 Openings
Elongated openings should be placed so that the long dimension is perpendicular, or as close to perpendicular as possible, to the dominant direction of travel....
-
§ 38.159(b)(2)(ii) Exception
Where the lift is designed to deploy with its long dimension parallel to the vehicle axis and which pivots into or out of the vehicle while occupied (i.e., “rotary lift”), the requirements...
-
2.2 Key Measurement Variables and Procedures
Body and wheelchair dimensions: Approximately 125 locations of body and wheelchair points recorded in three dimensions. 3....
