Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions. Question 5....
Search Results "Minimum Dimension"
-
M101.5 Dimensional Tolerances
-
Medical Device Manufacturers
supports; • Question 19 (c) on location and size of transfer supports; • Question 23 (a) on stirrups; • Question 24 (b) on positioning supports; • Question 29 (a) on alternative dimension...
-
M301.4.2 Clearance Around Base (Section-by-Section Analysis)
The proposed rule required a minimum clearance of 6 inches high measured from the floor and 36 inches deep measured from the edge of the examination surface. NPRM, 77 FR at 6927....
-
11B-505.6 Gripping surface
Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface. Exceptions: 1. ...
-
505.6 Gripping Surface
Where provided, horizontal projections shall occur 1 1/2 inches (38 mm) minimum below the bottom of the handrail gripping surface. EXCEPTIONS: 1....
-
R302.7.3 Horizontal Openings
Elongated openings in gratings shall be placed so that the long dimension is perpendicular to the dominant direction of travel....
-
A4.2.4 Clear Floor or Ground Space for Wheelchairs
A3 represent typical dimensions for a large adult male. The space requirements in this guideline are based upon maneuvering clearances that will accommodate most wheelchairs. Fig....
-
Corbin Russwin Inc. DC46900 Series Safeguard Door Closers
Minimum top rail 2-3/16". DC46925 Unit Push side mounted unit for right or left hand doors. Also suitable for double egress doors....
-
Can parking signage height be considered a "safe harbor"?
The 2010 ADA Standards, Section 502.6 requires parking signage to be located 60” minimum AFF or AFG to the bottom of the sign. 2010 ADA Standards, “502.6 Identification....
-
Introduction
Introduction This memo provides a revised description and analyses examining knee clearance dimensions in mammography equipment (as requested in your email dated: 4/15/2013)....
-
11B-604.9 Water closets and toilet compartments for children's use
Clarifies that when the suggested dimensions for children are used, the requirements for a single age group shall be applied consistently to the installation of a water closet and all associated...
-
4.1.3(12)(a)
Additional storage may be provided outside of the dimensions required by 4.25....
-
A4.2.4 CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS
A3 represent typical dimensions for a large adult male. The space requirements in this standard are based upon maneuvering clearances that will accommodate most larger wheelchairs....
-
4.1.2(11)
Additional storage may be provided outside of the dimensions shown in Fig 38....
-
Clear floor space
It appears that a minimum 6'-6" rear wall would be required if bench is parallel to a wall?...
-
9.2.2(4)
Additional storage may be provided outside of the dimensions required by 4.25....
-
C. Parking Slope
.: when measured as shown on the Tools & Techniques page , is the critical dimension 1/2" or less)?...
-
Jean Tessmer
Some of us prefer to mount to allow 28" knee clearance minimum to give the person in the wheelchair a lower shelf height of 32" depending on the thickness of your new #200 baby changer shelf...
-
5.8.2.1 Height of Breast Platform at Time of Measurement
Industry started with this dimension and determined the proportionate height of the breast platform to be 34 inches....
-
Braille Specifications
Section 703.3 provides specifications for braille, including the dimensions and position. Comment. Braille is to be located below the corresponding text....
-
505.6 Gripping Surface
Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface. [ECTCR UFAS 4.8.5(4), 4.9.4(4)] EXCEPTIONS: 1....
-
11B-505.6 Gripping surface
Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface. Exceptions: 1. ...
-
REDUCTION AND ANALYSIS OF DATA
The ADAAG set minimum criteria for accessibility of pedestrian facilities throughout the United States....
-
505.6 Gripping Surface
Where provided, horizontal projections shall occur 1½ inches (38 mm) minimum below the bottom of the handrail gripping surface. EXCEPTIONS: 1....
