Corada’s existing database of other accessibility-related material, so your question, comment, Opinion or Interpretation will be in context with applicable federal standards, regulations, technical...
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
FAQ: Why should I enter ADA references in my Voices post?
-
Q. Will the ADA increase litigation burdens on employers?
The Equal Employment Opportunity Commission, which has issued regulations implementing the ADA's title I employment provisions, published a technical assistance manual with guidance on how...
-
Section 35.130(h) Safety. (Section-by-Section Analysis)
Although the 1991 title II regulation did not include similar language, the Department's 1993 ADA Title II Technical Assistance Manual at II–3.5200 makes clear the Department's view that...
-
Section 35.151(c) Accessibility Standards for New Construction and Alterations (Section-by-Section Analysis)
the development of these proposed standards represents the culmination of a lengthy effort by the Access Board to update its guidelines, to make the federal guidelines consistent to the extent...
-
What surface characteristics are required of an accessible route?
No standards or methods of measurement are specified in scoping or technical provisions, although the Appendix to ADAAG contains advisory recommendations for slip resistance values derived...
-
Accessibility Guidelines for Pedestrian Facilities in the Public Right-of-Way
• Mail or Hand Delivery/Courier: Office of Technical and Informational Services, Access Board, 1331 F Street, NW, Suite 1000, Washington, DC 20004‒1111....
-
11B-228.3.2.1 Public use or common use EVCS
The electric vehicle charging station scoping requirements are new to CBC, as of 2016, complemented by new definitions in Section 202 and technical requirements in Section 11B-812. ...
-
5. Interoperability Requirements for Assistive Technology
First, to improve ICT-AT compatibility, the committee recommended updated—and more comprehensive—technical standards that require mainstream computer operating systems and software with...
-
Step 2: Identify the Presence of Limiting Factors
If the combined slope exceeds 1:2.5 (40 percent) for a continuous distance of 20 feet (6 meters) or more, document the length of trail that exceeds the technical requirements for slopes,...
-
11B-407.2.1.4 Location
Responding cars are programmed for maximum efficiency by reducing the number of stops any passenger experiences....
-
1009.2.1 Pool Lift Location
Where multiple pool lift locations are provided, no more than one pool lift shall be required to be located in an area where the water level is 48 inches (1220 mm) maximum....
-
11B-1009.5.4 Transfer steps
Transfer step height shall be 8 inches (203 mm) maximum. The surface of the bottom tread shall extend to a water depth of 18 inches (457 mm) minimum below the stationary water level....
-
703.4.1 Height above Finish Floor or Ground
characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches (1525 mm) maximum...
-
Section 4.26.2
Handrail gripping surfaces with a non-circular cross section must have a perimeter dimension of 4 inches to 6 ¼ inches, and a cross section dimension of 2 ¼ inches maximum....
-
M302.4.2 Clearance Around Base
The width of the base permitted within this clearance shall be 26 inches (660 mm) wide maximum at the edge of the examination surface and shall be permitted to increase at a rate of 1 inch...
-
M301.4.2 Clearance Around Base
The width of the base permitted within this clearance shall be 26 inches (660 mm) wide maximum at the edge of the examination surface and shall be permitted to increase at a rate of 1 inch...
-
403.5.3 Passing Spaces
An accessible route with a clear width less than 60 inches (1525 mm) shall provide passing spaces at intervals of 200 feet (61 m) maximum....
-
307.4 Vertical Clearance
The leading edge of such guardrail or barrier shall be located 27 inches (685 mm) maximum above the finish floor or ground....
-
5.8.2.7 Base Support Allowance
Base supports can be a maximum of 1½ inches high....
-
Gripping Surface Cross Section and Clearances M301, M302, and M305.2
The transfer supports shall be located at a maximum distance from transfer surface of 1 ½ inches....
-
R305.2.5 Pedestrian At-Grade Rail Crossings
The edge of the detectable warning surface nearest the rail crossing shall be 1.8 m (6.0 ft) minimum and 4.6 m (15.0 ft) maximum from the centerline of the nearest rail....
-
1009.5.4 Transfer Steps
Transfer step height shall be 8 inches (205 mm) maximum....
-
6. Fire Safety
Are fire-safety information, maximum room rate information, telephone and television information cards, guest services guides, restaurant menus, room service menus, and all other printed...
-
403.5.1 Clear Width
EXCEPTION: The clear width shall be permitted to be reduced to 32 inches (815 mm) minimum for a length of 24 inches (610 mm) maximum provided that reduced width segments are separated by...