Accessible parking spaces and access aisles are required to be level (maximum 1:48 slope) in all directions to provide a surface for wheelchair transfer to and from vehicles....
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
11B-502.4 Floor or ground surfaces
-
11B-502.4 Floor or ground surfaces
Accessible parking spaces and access aisles are required to be level (maximum 1:48 slope) in all directions to provide a surface for wheelchair transfer to and from vehicles....
-
Section 1630.2(g) Disability
The ADAAA retained the basic structure and terms of the original definition of disability....
-
1008.4.3 Play Tables
The tops of rims, curbs, or other obstructions shall be 31 inches (785 mm) high maximum....
-
307.4 Vertical Clearance
The leading edge of such guardrail or barrier shall be located 27 inches (685 mm) maximum above the finish floor or ground....
-
M302.4.1 Clearance in Base
Equipment components are permitted to be located within 8 inches (205 mm) maximum of the centerline of the clearance width....
-
M301.4.1 Clearance in Base
Components of diagnostic equipment are permitted to be located within 8 inches (205 mm) maximum of the centerline of the clearance width....
-
1607.8.2 Grab bars, shower seats and dressing room bench seats
room bench seat systems shall be designed to resist a single concentrated load of 250 pounds (1.11 kN) applied in any direction at any point on the grab bar or seat so as to produce the maximum...
-
1008.4.3 Play Tables
The tops of rims, curbs, or other obstructions shall be 31 inches (785 mm) high maximum....
-
703.4.1 Height Above Finish Floor or Ground
characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches (1525 mm) maximum...
-
407.2.1.4 Location
Responding cars are programmed for maximum efficiency by reducing the number of stops any passenger experiences....
-
407.2.1.4 Location
Responding cars are programmed for maximum efficiency by reducing the number of stops any passenger experiences....
-
703.4.1 Height Above Finish Floor or Ground
characters on signs shall be located 48 inches (1220 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest tactile character and 60 inches (1525 mm) maximum...
-
5.4.4.2 Transfer Support Distance from Transfer Surface Recommendation for Imaging Equipment
5.4.4.2 Transfer Support Distance from Transfer Surface Recommendation for Imaging Equipment The Committee recommends a maximum distance of 1 1/2 inches from the transfer surface to the...
-
410.6 Doors and Gates
EXCEPTION: Platform lifts serving two landings maximum and having doors or gates on opposite sides shall be permitted to have self-closing manual doors or gates....
-
403.5.3 Passing Spaces
An accessible route with a clear width less than 60 inches (1525 mm) shall provide passing spaces at intervals of 200 feet (61 m) maximum....
-
11B-403.5.3 Passing spaces
An accessible route with a clear width less than 60 inches (1524 mm) shall provide passing spaces at intervals of 200 feet (60,960 mm) maximum....
-
407.2.1.4 Location
Responding cars are programmed for maximum efficiency by reducing the number of stops any passenger experiences....
-
R304.2.3 Flared Sides
Where a pedestrian circulation path crosses the curb ramp, flared sides shall be sloped 10 percent maximum, measured parallel to the curb line. Advisory R304.2.3 Flared Sides....
-
4.5.3* Carpet
The maximum pile thickness shall be 1/2 in (13 mm) (see Fig. 8(f))....
-
Thresholds at Doorways [4.13.8]
ADAAG specifies a maximum threshold height of ½ inch, but allows a height up to ¾ inch at exterior sliding doors where necessary to prevent water damage....
-
M303.2.4.2 Knee Clearance
Knee clearance shall be provided at a depth of 11 inches (280 mm) minimum and 25 inches (635 mm) maximum at 9 inches (230 mm) above the floor and at a depth of 8 inches (205 mm) minimum...
-
M302.4.1 Clearance in Base
Equipment components are permitted to be located within 8 inches (205 mm) maximum of the centerline of the clearance width....
-
M301.4.1 Clearance in Base
Equipment components are permitted to be located within 8 inches (205 mm) maximum of the centerline of the clearance width....