In any action against a State for a violation of the requirements of this Act, remedies (including remedies both at law and in equity) are available for such a violation to the same extent...
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
§ 35.178 State immunity.
-
F247.5 Outdoor Constructed Features
, but not less than one, of each type of outdoor constructed feature provided at each location on trails, other than within facilities provided on trails, to comply with the applicable technical...
-
III-7.5190 Dressing and fitting rooms
Technical standards are provided for doors, benches, and mirrors, with less stringent standards for alterations....
-
g. Other relevant factors
Other relevant factors The nature of the work operation and the employer's organizational structure may be factors in determining whether a function is essential....
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent patient...
-
Number of Accessible Entrances
increasing scoping for public entrances (206.4.1 removing a requirement for accessible ground floor entrances (206.4.3 in the proposed rule) revision of provision for parking structure...
-
G.4.i. - Do the standards require a contractor's workplace to be Section 508 compliant?
For example, if a Federal agency enters into a contract to have a web site developed, the web site is required to meet the applicable technical provisions of the Access Board's standards...
-
"User Friendly" Guidelines
The Department recognizes that the Accessibility Guidelines include several highly technical provisions....
-
Section 35.151(i) Curb ramps (Section-by-Section Analysis)
In the NPRM, the Department stated that the phrase ‘‘other sloped areas'' lacks technical precision. The Department received no significant public comments on this proposal....
-
Fur out the wall
The centerline of the water closet shall be 16 inches (405 mm) minimum to 18 inches (455 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (430...
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADA Standards] 303.2 Vertical....
-
2. Automatic Identification Features
If your area’s emergency service provider has these features, you must ensure that TTY calls have the same access as voice calls to such enhanced features whenever feasible....
-
18) Elevators and platform lifts in new construction and alterations
Platform lifts may be substituted for elevators in new construction or alterations "if no other alternative is feasible" (§4.1.2(5))....
-
Transfer Steps: ADA Standard Section 1009.5.4
Transfer step height shall be 8 inches (205 mm) maximum....
-
Height: ADA Standard Section 1005.2.1
At least 25 percent of the railings, guards, or handrails shall be 34 inches (865 mm) maximum above the ground or deck surface....
-
Clear Width: ADA Standard Section 403.5.1
Section 403.5.1 covers the current ADA Standards for the clear width of walking surfaces that are part of an accessible route.
-
Signal Type: ADA Standard Section 407.4.8.2.1
Section 407.4.8.2.1 covers the current ADA Standards for the signal type of audible elevator car indicators.
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
11B-809.10.6.5 Thresholds
Where provided thresholds shall be 2 inches (51 mm) maximum in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from the horizontal...
-
11B-809.10.8.1 Location
The top of the lavatory rim shall be 34 inches (864 mm) maximum above the finished floor....
-
11B-809.10.6.4 Reinforcement for grab bars
Reinforcement for grabs bars shall comply with the following: Continuous reinforcement shall be installed in the walls of showers 30 inches (762 mm) maximum to 38 inches (965 mm) minimum...
-
11B-809.10.8.1 Location
The top of the lavatory rim shall be 34 inches (864 mm) maximum above the finished floor....
-
11B-809.9.4 Work surfaces
Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
-
11B-809.10.6.5 Thresholds
Where provided thresholds shall be 2 inches (51 mm) maximum in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from the horizontal...