Toilet paper dispensers shall comply with 309.4 and shall be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser...
Search Results "Feasibility (Technical, Infeasible, Structural, Maximum Extent)"
-
604.7 Dispensers
-
11B-228.3.2.1 Public use or common use EVCS
ETA Editor's Note The electric vehicle charging station scoping requirements were new to CBC as of 2016, complemented by new definitions in Section 202 and technical requirements in Section...
-
11B-228.3.2.1 Public use or common use EVCS
ETA Editor's Note The electric vehicle charging station scoping requirements were new to CBC as of 2016, complemented by new definitions in Section 202 and technical requirements in Section...
-
I. Need For and Final Objectives of the Guidelines.
These guidelines are applicable only to the extent that it is readily achievable to do so....
-
12206(c)(1) Rendering assistance
.-- Each Federal agency that has responsibility under paragraph (2) for implementing this Act may render technical assistance to individuals and institutions that have rights or duties under...
-
601.1 Scope (Section-by-Section Analysis)
601.1 Scope (Section-by-Section Analysis) This section proposes that the technical requirements for support documentation and services in this chapter be applied where either (a) required...
-
Gates and Barriers on Trails
Refer to the FSTAG for the technical provisions for gates and barriers....
-
11B-249.1.2
ETA Editor's Note The scoping and technical requirements for adult changing facilities are new in CBC 2019....
-
Ampetronic MLD5 MultiLoop Driver Hearing System
Most commonly used design types are low loss and low spill: MultiLoop™ Low Loss Systems are used to: Compensate for high losses due to metal structures Drive large areas where...
-
Ampetronic MLD7 MultiLoop Driver Hearing System
Most commonly used design types are low loss and low spill: MultiLoop™ Low Loss Systems are used to: Compensate for high losses due to metal structures Drive large areas where...
-
11B-608.9 Shower floor or ground surface
Floor or ground surfaces of showers shall comply with Section 11B-302.1 and shall be sloped 1:48 maximum in any direction....
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
11B-608.9 Shower floor or ground surface
Floor or ground surfaces of showers shall comply with Section 11B-302.1 and shall be sloped 1:48 maximum in any direction....
-
11B-1002.4.4.3 Permitted protrusions in wheelchair spaces
Objects are permitted to protrude a distance of 6 inches (152 mm) maximum along the front of the wheelchair space, where located 9 inches (229 mm) minimum and 27 inches (686 mm) maximum...
-
1002.4.4.3 Permitted Protrusions in Wheelchair Spaces
Objects are permitted to protrude a distance of 6 inches (150 mm) maximum along the front of the wheelchair space, where located 9 inches (230 mm) minimum and 27 inches (685 mm) maximum...
-
Standard Roll-In Type Shower Compartments: ADA Standard Section 608.3.2
Section 608.3.2 covers the current ADA Standards for grab bars in standard roll-in type shower compartments.
-
11B-505.5 Clearance
Handrails may be located in a recess if the recess is 3 inches (76 mm) maximum deep and 18 inches (457 mm) minimum clear above the top of the handrail....
-
11B-1009.5.4 Transfer steps
Transfer step height shall be 8 inches (203 mm) maximum....
-
11B-1009.5.4 Transfer steps
Transfer step height shall be 8 inches (203 mm) maximum....
-
11B-505.5 Clearance
Handrails may be located in a recess if the recess is 3 inches (76 mm) maximum deep and 18 inches (457 mm) minimum clear above the top of the handrail....
-
1017.10 Trailhead Signs
Typical and maximum running slope; and 5. Typical and maximum cross slope....
-
407.8.3.2 Obstructed Forward Reach
Where the operable part is located beyond the leading edge of the maximum protrusion within the length of the vertical reference plane, the operable part shall conform to 407.8.3.2....
-
1017.10 Trailhead Signs
Typical and maximum running slope; and 5. Typical and maximum cross slope....
