. ______________________________________ UNITED STATES DISTRICT JUDGE Signatures indicating agreement to entry of this Consent Decree: For the United States of America: Date...
Search Results "Unit of Measurement"
Filters
Commonly Searched Documents
-
Signatures and Contact Information Page
-
BACKGROUND
The United States alleges that the claimants listed in paragraph 24 below, are individuals with disabilities within the meaning of 42 U.S.C. § 12111(8)....
-
SETTLEMENT AGREEMENT BETWEEN THE UNITED STATES OF AMERICA AND EDX INC. UNDER THE AMERICANS WITH DISABILITIES ACT DJ No. 202-36-255
[See subsections ...]
-
End of Document
For the United States of America Executed this ______ day of ________________ 2016....
-
ACCESS NOW, INC. v. AMBULATORY SURGERY CENTER GROUP, LTD.
UNITED STATES DISTRICT COURT FOR THE SOUTHERN DISTRICT OF FLORIDA MIAMI DIVISION CASE NO. 99-109-CIV-GARBER ACCESS NOW, INC., et. al, Plaintiffs, v....
-
15(c)
(c) HWI agrees that it shall voluntarily submit to the United States within 120 days of each survey the HWI Hotels Survey Report, including photographs, and a list of the remediation items...
-
§ 36.606(a)(2)
By the same token, certification would not be relevant to construction of a facility for children, if the regulations against which equivalency is measured do not address children´s facilities...
-
4 [§ 4.7.2]
To measure the gutter slope, place the level in the same position as the arrow in the illustration, with one end where the gutter meets the ramp and the other end towards the street....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
R305.2 Placement
Where the back of curb edge is tooled to provide a radius, the border dimension should be measured from the end of the radius....
-
4.1.6(4)(d)
(ii) If existing thresholds measure 3/4 in (19 mm) high or less, and are beveled or modified to provide a beveled edge on each side, then they may be retained....
-
§ 37.135(d) Phase-in of implementation
If the date for full compliance specified in the plan is after January 26, 1993, the plan shall include milestones, providing for measured, proportional progress toward full compliance....
-
Bradley Standard Series Vertical Recessed Soap Dispenser
Tumbler lock keyed like other Bradley units. SOAP VALVE: chrome-plated brass with ABS mechanism. Requires less than 5 lbs. of force to dispense soap....
-
4.3.1 General
Where provided, tent pads and tent platforms at single camping units shall comply with section 4.6 and shall be connected to an ORAR complying with section 2.0....
-
Wheelchair Access
If phones are installed as single units, one per floor must be accessible....
-
American Specialties Folding Shower Seat 8206-L
Seat measures 33" (840 mm) wide and projects 22 7/8" (580 mm) from wall....
-
F206.2.3 Multi-Story Buildings and Facilities
, all common use areas serving residential dwelling units with mobility features required to comply with 809.2 through 809.4, and public use areas serving residential dwelling units are...
-
E. IMPLEMENTATION AND ENFORCEMENT
If the United States believes that the Museum is not in compliance with this Agreement or any requirements contained herein, the United States agrees to notify the Museum in writing of the...
-
11B-404.2.4.3 Recessed doors and gates
457 mm) of the latch side at an interior doorway, or within 24 inches (610 mm) of the latch side of an exterior doorway, projects more than 8 inches (203 mm) beyond the face of the door, measured...
-
Notes
II The IDeA Center in its research defined wheelchair wheelbase as the distance from the center of the primary drive wheel to the center of the caster measured parallel to the floor....
-
1016.5 Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
Slip Resistance
While different measurement devices and protocols have been developed over the years for use in the laboratory or the field, a widely accepted method has not emerged....
-
Clearance Around Base (M301.4.2 and M302.4.2)
M301.4.2 and M302.4.2 would require the base of the equipment to provide a clearance 6 inches high minimum measured from the floor and 36 inches deep minimum measured from the edge of the...
-
225(b)(1) In general
(1) In general In order to carry out the purposes established under section 151 of this title, to make available to all individuals in the United States a rapid, efficient nationwide...
