(a) Any stepwell or doorway with a lift, ramp or bridge plate immediately adjacent to the driver shall have, when the door is open, at least 2 foot-candles of illumination measured on the...
Search Results "Unit of Measurement"
-
§ 38.81(a)
-
604.9.3 Height
The height of water closets shall be 11 inches (280 mm) minimum and 17 inches (430 mm) maximum measured to the top of the seat....
-
XII. Examinations and Courses
In order to provide an examination in an accessible place and manner, a private entity must -- Assure that the examination measures what it is intended to measure, rather than reflecting...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
ASSESSMENT, PROGRESS, ACHIEVEMENT, AND GRADING
Assessment instruments that compare the individual against herself or himself are able to measure both attainment and growth....
-
III-4.4300 Standards to apply
Measures taken to remove barriers should comply with the ADA Accessibility Guidelines (ADAAG) contained in the appendix to the Department's rule....
-
Standardized Tests of Physical Fitness and Community Ambulation
Resting heart rate and energy consumption were measured with the subject seated or reclining on a couch. Heart rate was measured with a Polar heart rate monitor (Polar Vantage XL)....
-
What values are recommended for ground and floor surfaces along an accessible route?
In the study sponsored by the Access Board, laboratory measurements from a Kistler force plate and computer analysis of the gaits of persons with mobility impairments (including crutch users...
-
Capabilities, Resources, and Facilities
hands-on experience with the measurement of all classes of anthropometric dimensions. hands-on experience with experimental subjects and human use considerations....
-
4.5 Weight Scales
In certain circumstances, such as setting chemotherapy dosages, weight is often a critical measurement....
-
Test Procedures
Accessibility Measures All surfaces were measured with the rotational penetrometer periodically over the first 6 months of exposure (Fig. 9)....
-
B. Technical standards for criterion-related validity studies
The possibility of bias should be considered both in selection of the criterion measures and their application....
-
4.1.2(5)(d)(ii)
(ii) Units and facilities that specialize in treatment or services for persons with mobility impairments: 20 percent of the total number of parking spaces provided serving each such unit...
-
607 Bathtubs
Specifications for bathtubs in section 607 address clear floor space, seats, grab bars, operable parts, shower spray units, and enclosures....
-
SCOTT JOHNSON v. STARBUCKS CORPORATION - AMICUS BRIEF
ANDERSON (CABN 149604) United States Attorney SARA WINSLOW (DCBN 457643) Chief, Civil Division ELLEN LONDON (NYRN 4605671) Assistant United States Attorney 450 Golden Gate Avenue...
-
TEST NO. 2 – SITE ANALYSIS TEST
In no case shall less than 20 percent of the ground floor dwelling units be on an accessible route and comply with the provisions of Division IV. 3....
-
TEST NO. 2 – SITE ANALYSIS TEST
In no case shall less than 20 percent of the ground floor dwelling units be on an accessible route and comply with the provisions of Division IV....
-
Access-Able Designs Tub Transfer Bench SH-414-2SDL
Measures 25" W x 15" D. Custom sizes available. 5 year warranty....
-
703.5.8 Character Spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
703.5.8 Character Spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
T304.3 Location
Operable parts provided at a wheelchair space shall be located adjacent to the wheelchair space 24 inches (610 mm) minimum and 36 inches (915 mm) maximum from the rear of the wheelchair space measured...
-
T702.6 Character Spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
T502.2 Doorways with Lifts, Ramps or Bridgeplates
Vertical clearance shall be measured from the inside finished edge of the door opening to the highest point of the deployed lift, ramp or bridgeplate below....
