The United States Attorney's Office for the District of Connecticut and the United States Department of Justice (collectively the Department) initiated this investigation pursuant to title...
Search Results "Unit of Measurement"
Commonly Searched Documents
-
SCOPE OF THE INVESTIGATION
-
1132A.4, Item 5
In buildings containing covered multifamily dwelling units, the floor or landing immediately outside the entry may be sloped up to ¼ inch (6.35 mm) per foot (12 inches) (305 mm), in a direction...
-
11B-703.8.4 Character height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
1.5 Materials
The reflectance factors were measured on a different day using a Minolta CS-100 Chroma Meter....
-
4.1 Wheeled Mobility Device Dimensions
Thus, specifying exactly how it is measured is important for comparing results....
-
4.35.5 Mirror
Where mirrors are provided in dressing rooms of the same use, then in an accessible dressing room, a full-length mirror, measuring at least 18 in wide by 54 in high (460 mm by 1370 mm),...
-
Question 23
The Department seeks input regarding the impact the measures being contemplated by the Department with regard to accessible equipment and furniture will have on small entities if adopted...
-
7c.
Is there clear maneuvering floor space in front of each accessible door (see Figure 25 in the appendix for measurements) and on the pull side, is there at least 18 inches clear floor space...
-
M303.2.6 Edge Protection
Where wheelchair spaces are provided on a platform raised more than 1 ½ inches (38 mm) in height, edge protection 2 inches (51 mm) high minimum measured from the surface of the platform...
-
Actions which Constitute Discrimination
Failing to use employment tests in the most effective manner to measure actual abilities....
-
General: ADA Standard Section 403.1
Section 403.1 of the ADA Standards covers information in the current ADA Standards for walking surfaces that are part of an accessible route.
-
Platform Lifts: ADA Standard Section 207.2
Section 207.2 covers scoping requirements in the most current ADA Standards for platform lifts used as part of an accessible means of egress.
-
Readily Achievable
action; the number of persons employed at the site; the effect on expenses and resources; legitimate safety requirements that are necessary for safe operation, including crime prevention measures...
-
Obstructed High Reach: ADA Standard Section 308.3.2
Section 308.3.2 covers the current ADA Standards for obstructed high side reach.
-
11B-703.7.2.6 Toilet and bathing facilities geometric symbols
Geometric symbols at entrances to toilet and bathing rooms shall be mounted at 58 inches (1473 mm) minimum and 60 inches (1524 mm) maximum above the finish floor or ground surface measured...
-
11B-308.3.2 Obstructed high reach
Operable parts of fuel dispensers shall be permitted to be 54 inches (1372 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
- Delta Touch2O® Technology by Delta Faucet
-
VI. ENFORCEMENT
, regulations, or rules administered by the United States or to prevent or limit the right of the United States to obtain relief for other violations of the ADA, or other federal law. ...
-
Sec. 12205. Attorney's fees. [Section 505]
In any action or administrative proceeding commenced pursuant to this chapter, the court or agency, in its discretion, may allow the prevailing party, other than the United States, a reasonable...
-
Forward Approach
Forward Approach Clear floor space is required to the face of the unit; a portion can be provided below the unit where clearance is available for toes/knees....
-
Scope: ADA Standard Section 201.1
Section 201 discusses the scope of the ADA Standards.
-
1.1.7.3.1 Detached one- and two-family dwellings
Detached one- and two-family dwellings, lodging houses, live/work units, townhouses not more than three stories above grade plane in height with a separate means of egress, and their accessory...
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
Tools and Documentation
The following tools are needed for the 2016 Checklist: a metal tape measure at least 20 feet long a digital level or a bubble level that is at least 24 inches long a door pressure...