detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (17 mm) minimum, measured...
Search Results "Unit of Measurement"
Filters
Commonly Searched Documents
-
705.1.2 Dome Spacing
-
605.2 Height and Depth
Urinals shall be 13 1/2 inches (345 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture....
-
705.1.2 Dome Spacing
detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (17 mm) minimum, measured...
-
Running Slope (Grade)
The ascent or descent of a trail segment expressed as a percentage of its length, which is the difference in elevation of a section of a trail measured parallel to the predominant direction...
-
4.9.2 TREADS AND RISERS
Stair treads shall be no less than 11 in (280 mm) wide, measured from riser to riser (see Fig. 18(a)). Open risers are not permitted on accessible routes....
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
9. Timeshares, Condominium Hotels, and Other Places of Lodging
The final rule limits obligations for units that are not owned or substantially controlled by a public accommodation that operates a place of lodging....
-
10.1 Q. Is it necessary to have an accessible path of travel from a subterranean garage to single-story covered multifamily dwellings built on top of the garage?
To satisfy Requirement 1 of the Guidelines, there would have to be an accessible route leading to grade level entrances serving the single-story dwelling units from a public street or sidewalk...
-
4.1.4(11)(c)
Facilities Application One and two family dwelling: Federally assisted, rental 5 percent of the total, or at least one unit, whichever is greater...
-
BACKGROUND
The parties to this Settlement Agreement are the United States of America and Aurora Health Care, Inc. ("Aurora")....
-
TEST NO. 3 – UNUSUAL CHARACTERISTICS TEST
The original site characteristics result in a difference in finished grade elevation exceeding 30 inches (762 mm) and 10 percent measured between an entrance and all vehicular or pedestrian...
-
5.7.1 Lift Compatibility Clearance in Base for M301
The base of the equipment shall provide a clearance 44 inches wide minimum, 6 inches high minimum measured from the floor, and 36 inches deep minimum measured from the edge of the examination...
-
11B-604.7 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 _|Operation|_ and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the...
-
3-D Shape Digitization
3-D Shape Digitization Currently in the forefront of measuring methodology for anthropometric studies is 3-D shape digitization....
-
Salsbury Industries Designer Wood Locker
Requires the Registered User plan or above. Login! -
§ 35.175 Attorney's fees.
In any action or administrative proceeding commenced pursuant to the Act or this part, the court or agency, in its discretion, may allow the prevailing party, other than the United States...
-
THE PARTIES
The United States Department of Justice is the federal agency responsible for administering and enforcing title III of the Americans with Disabilities Act of 1990 ("ADA"), 42 U.S.C. § 12181...
-
Americans with Disabilities Act (ADA) of 1990 (with amendments issued through 2008)
The ADA was originally enacted in public law format and later rearranged and published in the United States Code....
-
1009.2.4 Seat Height
The height of the lift seat shall be designed to allow a stop at 16 inches (405 mm) minimum to 19 inches (485 mm) maximum measured from the deck to the top of the seat surface when in the...
-
ADA Gap Tool
ADA Gap Tool This handy tool was developed by Evan Terry Associates to assist its surveyors in measuring gaps in ground or floor surfaces....
-
502.6 Identification
Signs shall be 60 inches (1525 mm) minimum above the finish floor or ground surface measured to the bottom of the sign....
-
Side Reach [§308.3]
The maximum reach depth for this range is 10” measured from the available clear floor space....
-
§ 37.139(d)(5)
The plan shall include milestones for implementing phases of the plan, with progress that can be objectively measured yearly;...
-
11B-813.2.1.3 Height and operation
Adult changing table height shall be adjustable from 17 inches (432 mm) above the floor or ground to 38 inches (965 mm) above the floor or ground, as measured to the top of the changing...
