met: (a) the cabinetry can be removed without removal or replacement of the kitchen work surface; (b) the finish floor extends under the cabinetry; and (c) the walls...
Search Results "Control End Wall"
-
11B-804.3.1 Clear floor or ground space
-
II. Systemic Considerations
Training criminal justice personnel, conducting reviews of policies and procedures, and collaborating with mental health and disability services providers are three ways to achieve that end...
-
604.8.1.2 Doors
Doors shall be located in the front partition or in the side wall or partition farthest from the water closet....
-
604.2 Location
The water closet shall be positioned with a wall or partition to the rear and to one side....
-
Bathroom Accommodating Reduced Ambulatory Mobility
Soap dispenser (to prevent a fall from retrieving bar soap from the floor) Vertical and horizontal shower grab bars Hidden fold-down grabs bars next to the toilet Wall...
-
11B-604.8.1.1 Size
Wheelchair accessible compartments shall be 60 inches (1524 mm) wide minimum measured perpendicular to the side wall, and 56 inches (1422 mm) deep minimum for wall hung water closets and...
-
Car Dimensions: ADA Standard Section 407.4.1
Section 407.4.1 covers the current ADA Standards for elevator car dimensions.
-
Maintenance
routes, such as filling ruts, reshaping a trail bed, replacing or reshaping surfacing material, repairing washouts, installing riprap to retain cut and fill slopes, constructing retaining walls...
-
Tom Williams, AIA, National Accessibility Officer, GSA, Public Buildings Service
Well, this whole myriad of starting with the exterior of the building wall....
-
Height from Finish Floor or Ground: ADA Standard Section 703.5.6
EXCEPTION: Visual characters indicating elevator car controls shall not be required to comply with 703.5.6....
-
804.2.1 Pass Through Kitchen
In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing...
-
1134A.8, Item 1
Vanities and lavatories shall be installed with the centerline of the fixture a minimum of 18 inches (457 mm) horizontally from an adjoining wall or fixture to allow for forward approach...
-
Intensity
Intensity To be effective, a visual signal (or its reflection from adjacent walls and ceiling) must be of an intensity that will raise the overall light level sharply, but not be so intense...
-
1134A.8, Item 1
Vanities and lavatories shall be installed with the centerline of the fixture a minimum of 18 inches (457 mm) horizontally from an adjoining wall or fixture to allow for forward approach...
-
ASME
The enclosure walls not used for entry or exit are required to have a grab bar the full length of the wall on platform lifts....
-
Accessible Pathway & Corridor: Minimum Clear Width Required for 180-degree Turn Around Barrier
These data are based on measurements of wheeled mobility users performing 180-degree turns around an obstruction, built with mock walls....
-
E2-a
[ADA Standards § 4.4.1] Yes No Note: These objects may be wall mounted or free standing....
-
Dimensions: ADA Standard Section 810.2.2
Board’s Note to Reader: The Department of Transportation’s ADA standards indicate that compliance is required to the extent construction specifications are within a public entity's control...
-
ADA Sign Depot Men's Accessible Restroom Wall Sign with Tactile Text and Grade 2 Braille - 6" x 8"
Men's Bathroom Sign Wheelchair Accessible Tactile Braille ADA Compliant Sign 6" x 8" size ADA compliant non-glare matte finish ADA compliant font and...
-
Minimum Number: ADA Standard Section 234.3
Section 234.3 covers scoping requirements in the current ADA Standards for the minimum number of wheelchair spaces required at amusement rides.
-
Sloped Surfaces
Rest one end of the level at the highest point of the sloped surface and lift the other end (see image) until the bubble is in the middle of the tube. This is the "level" position....
-
11B-104.1.1 Construction and manufacturing tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
11B-104.1.1 Construction and manufacturing tolerances
All dimensions are subject to conventional industry tolerances except where the requirement is stated as a range with specific minimum and maximum end points....
-
BlueDAG Software and Mobile Application
BlueDAG is a cloud-hosted software system for end-to-end management of ADA evaluation and compliance initiatives....
