The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
Search Results "Control End Wall"
-
11B-610.3.1 Rectangular seats
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
11B-604.7.2 Disposal units
Sanitary napkin disposal units, if provided, shall comply with Section 11B-309.4 and shall be wall mounted and located on the sidewall between the rear wall of the toilet and the toilet...
-
§100.7(a)(2)
(2) For purposes of determining liability under paragraphs (a)(1)(ii) and (iii) of this section, prompt action to correct and end the discriminatory housing practice may not include any...
-
Pilot Rock WPTS Square Frame Table Using Recycled Plastic
Series Overview Model WPTS Picnic Tables are accessible to wheelchairs at both ends. ...
-
Pilot Rock WPTS Square Frame Table Using Lumber
Series Overview Model WPTS Picnic Tables are accessible to wheelchairs at both ends. ...
-
Parallel Parking Spaces (R309.2) (Section-by-Section Analysis)
In alterations where the street or sidewalk adjacent to the parking spaces is not altered, an access aisle is not required provided the parking spaces are located at the end of the block...
-
5.3.2.1 Transfer Sides Recommendation for Stretchers
The configuration of stretchers typically does not allow access to a transfer surface on either end....
-
4.4.4 Clear Floor or Ground Space
A clear floor or ground space of 36 inches (915 mm) by 48 inches (1220 mm) shall be located at an end the bench with one side of the space adjoining an accessible route, outdoor recreation...
-
Taking Measurements
Rest one end of the level at the highest point of the sloped surface and lift the other end (as shown in the illustration) until the bubble is in the middle of the tube....
-
A4.4.1 General
The touch technique is used primarily in uncontrolled areas, while the diagonal technique is used primarily in certain limited, controlled, and familiar environments....
-
604.2 Location
The water closet shall be positioned with a wall or partition to the rear and to one side....
-
704.11.1 Parapet construction
Parapets shall have the same fire-resistance rating as that required for the supporting wall, and on any side adjacent to a roof surface, shall have noncombustible faces for the uppermost...
-
907.4.2.2 Height
CBC Section 11B-309.4 requires controls and operating mechanisms to be operable with one hand without tight grasping, pinching or twisting of the wrist (must be operable by persons with...
-
907.4.2.2 Height
CBC Section 11B-309 requires controls and operating mechanisms to be operable with one hand without tight grasping, pinching or twisting of the wrist (must be operable by persons with limited...
-
4.34.5.4(2) Seat
An in-tub seat or a seat at the head end of the tub shall be provided as shown in Fig. 33 and 34. The structural strength of seats and their attachments shall comply with 4.26.3....
-
M305.3.2 Vertical Position
Where the support is vertical, it shall be 18 inches (455 mm) minimum in length and the bottom end of the support shall be 34 inches (865 mm) high minimum and 37 inches (940 mm) high maximum...
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
804.2.1 Pass Through Kitchen
In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing...
-
11B-804.2.1 Pass through kitchen
In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing...
-
11B-604.7.2 Disposal units
Sanitary napkin disposal units, if provided, shall comply with Section 11B-309.4 and shall be wall mounted and located on the sidewall between the rear wall of the toilet and the toilet...
-
11B-804.2.1 Pass through kitchen
In pass through kitchens where counters, appliances or cabinets are on two opposing sides, or where counters, appliances or cabinets are opposite a parallel wall, clearance between all opposing...
-
Pilot Rock APTX Full Sized Pedestal Rectangular Utility Table Using Lumber
Specifications: FRAME: Two heavy pedestal posts of 3" x 6" x 1/8" wall rectangular steel tubing to support the table top. ...
-
Pilot Rock APTX Full Sized Pedestal Rectangular Utility Tables Using Recycled Plastic
Specifications: FRAME: Two heavy pedestal posts of 3" x 6" x 1/8" wall rectangular steel tubing to support the table top. ...
