SECTION 1118B - SPACE ALLOWANCE AND REACH RANGES 1118B.6 Side reach. ...
Search Results "Latch Side Clearance"
Filters
Commonly Searched Documents
-
1118B.6
-
C) Accessible Entrance
If a door is provided, there must be maneuvering space on the pull and push sides of the door to permit a person using a wheelchair to open the door and then move through the door opening...
-
Temporary Solutions for Election Day: Accessible Entrance to Polling Place
Problem Three: Entrance door threshold has an abrupt change in level of more than 1/4 inch and no beveled sides....
-
Are doors or gates to employee work areas required to comply?
Entry doors or gates to employee work areas are required to meet applicable requirements, including those for maneuvering clearance, on the exterior, but not the interior....
-
Clear Deck Space
This will allow persons using a wheelchair to turn around and access the wall, depending on the side they can best use to transfer....
-
Rockwood Manufacturing Company 596S Hospital Push Pull Latch 2-3/4" Backset
Material: Stainless Steel FEATURES: • Easy to operate low-force paddle. • Non-handed (except for engraved models). • Includes Standard 161 and ASA strike. • 2-3/4", 5" or 7"...
-
Accessible Parking Video Fact Sheet
Troy Balthazor, ADA Specialist for the Great Plains ADA Center, gives an overview of accessible parking requirements from the 2010 ADA Standards for Accessible Design. Technical...
-
Water Closet Clear Floor Space in Toilet Compartments
Other criteria for toilet rooms, including turning space, maneuvering space at doors, and clearances at other fixtures, typically results in additional clearance at water closets not in...
-
Grab Bars
If only one bar is provided, the clearance must be a minimum of 24 inches on each side of the bar....
-
1009.4.5 Grab Bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
What is an accessibility evaluation survey and when is one needed?
The measuring tape is stretched from the face of the door to the nearest portion of the doorframe or latch mechanism on the latch side....
-
AJW Architectural Products U719 96"W x 48"H J-Mold Mirror - Four Sided Frame - Plate Glass
Product Features Fabricated of #18 gauge stainless steel with #4 satin finish Mirror features a "J" type channel frame Multiple reflective surfaces available Mirror comes...
-
11B-1009.4.5 Grab bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
11B-1009.4.5 Grab bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
M302.4 Lift Compatibility (Section-by-Section Analysis)
M302.4.1) or clearance around base (proposed M302.4.2) technical requirements....
-
Technical Memorandum TM 2017-25 Door and Gate Surfaces
Effective Date: April 1, 2017 2012 TAS Reference: 404.2.10 404.2.10 requires door and gate surfaces within 10 inches (255mm) of the finish floor to have a smooth surface on the push side...
-
Figure 1003.3.1 Boat Slip Clearance – Drawing from the U.S. Access Board
-
Figure 1003.3.2 Boarding Pier Clearance – Drawing from the U.S. Access Board
-
Mounting Height and Location
Tactile signs are required to be located alongside the latch side of doors so that clear floor space at least 18 by 18 inches, centered on the tactile characters, is provided outside the...
-
1009.4.5 Grab Bars
Where one grab bar is provided, clearance shall be 24 inches (610 mm) minimum on both sides of the grab bar....
-
Toilet Room Doors
Concerns were raised that permitting doors of single-user toilet or bathing rooms with in-swinging doors to swing into the clearance around any fixture will result in inaccessibility to...
-
Gates and Barriers
In such circumstances, 32 inches (815 millimeters) clearance, the same as is required for an interior door, will provide pedestrian access to the recreation opportunity without permitting...
