In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
Search Results "Cross Slope"
Commonly Searched Documents
-
4.4.1 General
-
Electronic instruments
Originally created to measure the flatness of concrete floors in critical applications such as narrow - aisle warehouses, these devices can be used to measure slope flatness....
-
Three Additional Features for Van-Accessible Parking Spaces
accessible" and the international symbol of accessibility mounted high enough so the sign can be seen when a vehicle is parked in the space 96" min. width access aisle, level (max. slope...
- Armor-Tile Tactile Systems Modular Paver Systems
- Tork Elevation® Matic® Hand Towel Roll Dispenser with Intuition® Sensor, Black
- Disability Resource Center (dRC) - Fredericksburg, VA
- Salsbury Industries See Through Metal Locker Double Tier 3 Wide
- Salsbury Industries See Through Metal Locker Double Tier 1 Wide
- Salsbury Industries See Through Metal Locker Triple Tier 3 Wide
- Salsbury Industries See Through Metal Locker Triple Tier 1 Wide
- AJW Architectural Products U590 1.6 Gallon Sanitary Napkin Disposal w/ Keyed Access Panel - Surface Mounted
- Ramp NOW Alumiramp Modular Ramps
-
References
Effects of cross slopes on the mobility of manual wheelchair users. Assistive Technology. 2012; 24(2):102-9. Kaye, H. S., Kang, T. and LaPlante, M.P. (2000)....
-
R202 Alterations and Elements Added to Existing Facilities (Section-by-Section Analysis)
For example, if a new bench is installed on an existing sidewalk that has a cross slope exceeding 2 percent, the sidewalk is not required to be altered to reduce the cross slope because...
-
11B-233.3.1.2.6.1 Single building with one common (lobby) entrance
Test No. 1 -- Individual Building Test may only be used if the site has terrain over 15 percent slope. Test No. 3 -- Unusual Characteristics Test may be used if applicable....
-
11B-810.2.3 Connection
boarding and alighting areas shall provide a detectable transition between the boarding/alighting area and the roadway; the detectable transition shall consist of a curb with the face sloped...
-
303.3 Beveled
Changes in level between 1/4 inch (6.4 mm) high minimum and 1/2 inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2. Advisory 303.3 Beveled....
-
Tent Pads and Tent Platforms [1013]
Tent pads and tent platforms must comply with the technical requirements for clear ground space and slope. Tent platforms must also comply with the technical requirements for height....
-
10.1 Q. Is it necessary to have an accessible path of travel from a subterranean garage to single-story covered multifamily dwellings built on top of the garage?
This may be provided either by a properly sloped ramp leading from the below grade parking to grade level, or by means of an elevator from the parking garage to the dwelling units....
-
4.6.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
-
1013.1 General
The technical requirements address the clear ground space around tent pads and tent platforms (1013.2); the slope of tent pads, tent platforms, and clear ground spaces (1013.2); and the...
-
11B-810.2.3 Connection
boarding and alighting areas shall provide a detectable transition between the boarding/alighting area and the roadway; the detectable transition shall consist of a curb with the face sloped...
-
11B-810.2.3 Connection
boarding and alighting areas shall provide a detectable transition between the boarding/alighting area and the roadway; the detectable transition shall consist of a curb with the face sloped...
-
11B-206.2.1 Site arrival points
(1) Newly constructed or altered streets, roads, and highways must contain curb ramps or other sloped areas at any intersection having curbs or other barriers to entry from a street...