Window Ease™ attaches to any manufactured single-hung, double-hung or horizontal sliding window....
Search Results "Horizontal Standing Support"
- Window Ease
- Southwest Home Products Window Ease Latching System
-
504.2.1 Preservation of Accessibility Information in Format Conversion (Section-by-Section Analysis)
Analysis) This section proposes that authoring tools, when converting content or saving content in multiple formats, must preserve information required for accessibility to the extent supported...
-
Stress Management
Provide praise and positive reinforcement Refer to EAP Allow employee to make telephone calls for support Provide sensitivity training for workforce Allow the presence and use of...
-
4.28.3(7)
(7) In general, no place in any room or space required to have a visual signal appliance shall be more than 50 ft (15 m) from the signal (in the horizontal plane)....
-
4.9.4(2)
At the bottom, the handrail shall continue to slope for a distance of the width of one tread from the bottom riser; the remainder of the extension shall be horizontal (see Fig. 19(c) and...
-
§ 38.53(d)(1) Requirements
Where new vehicles will operate in new stations, the design of vehicles shall be coordinated with the boarding platform design such that the horizontal gap between each vehicle door at rest...
-
§ 38.173(b)
(b) Where the vehicle covered by paragraph (a) will operate in an accessible station, the design of vehicles shall be coordinated with the boarding platform design such that the horizontal...
-
11B-216.4.1 Exit doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
§382.27(c)(8)
(8) Transportation of an emotional support or psychiatric service animal in the cabin;...
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
4. Wheelchair seat depth
Wheelchair seat depth For this study, wheelchair seat depth was calculated as the horizontal distance from the proximal (i.e., towards the rear) edge to the distal (i.e., towards the...
-
2.2 Lighting Conditions
On each trial one measurement of horizontal illuminance was manually recorded from a Minolta T-1 Illuminance meter....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
404.2.10 Door and Gate Surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other....
- seca 684 r Digital Multifunctional Scale with Integrated RS232 Interface
-
12209(a)(1) Commitment to Rule XLII
.-- The Senate reaffirms its commitment to Rule XLII of the Standing Rules of the Senate which provides as follows: No member, officer, or employee of the Senate shall, with respect to...
-
Exceptions [1014.1, Exceptions 1 and 2]
Many times, the roof of a camp shelter is sloped or does not permit someone to stand fully erect while in the shelter....
-
4.6.6 Passenger Loading Zones
Vehicle standing spaces and access aisles shall be level with surface slopes not exceeding 1:50 (2%) in all directions....