The identification fixture shall be 80 inches (2032 mm) minimum above the finish floor or ground to the bottom of the fixture....
Search Results "Minimum Dimension"
-
11B-411.2.2.1 Visible identification
-
11B-219.3 Receivers
The minimum number of receivers to be provided shall be equal to 4 percent of the total number of seats, but in no case less than two....
-
11B-219.3 Receivers
The minimum number of receivers to be provided shall be equal to 4 percent of the total number of seats, but in no case less than two....
-
5.2.1.1 Transfer Surface Width Recommendations for M301
5.2.1.1 Transfer Surface Width Recommendations for M301 The Committee recommends a transfer surface of 28 inches minimum width for equipment used by patients in a supine, side-lying,...
-
Doors: ADA Standard Section 604.8.2.2
Section 604.8.2.2 covers the current ADA Standards for ambulatory accessible compartment doors.
-
11B-407.2.2.2 Visible signals
Visible signal fixtures shall be centered at 72 inches (1829 mm) minimum above the finish floor or ground....
-
11B-407.2.2.2 Visible signals
Visible signal fixtures shall be centered at 72 inches (1829 mm) minimum above the finish floor or ground....
-
11B-809.1.2 Viewing devices
with a viewing device for a standing person, the primary entry door to a residential dwelling units with mobility features shall also provide a lower viewing device 42 inches (1067 mm) minimum...
-
Bobrick ClassicSeries Surface Mounted Seat-Cover Dispenser B-221
Allow 5" (125mm) minimum clearance from bottom of dispenser to top of any horizontal projection for filling dispenser from below unit....
-
Listen Technologies ADA Assistive Listening Device Calculator
The calculator allows you to enter the number of seats in a venue to calculate the minimum number of assistive listening devices and neck loops needed to meet new 2010 ADA requirements....
-
Size: ADA Standard Section 407.4.8.1.1
Section 407.4.8.1.1 covers the current ADA Standards for size of visible elevator car position indicators.
-
11B-407.4.8.1.1 Size
Characters shall be ½ inch (12.7 mm) high minimum....
-
11B-407.4.8.1.1 Size
Characters shall be ½ inch (12.7 mm) high minimum....
-
Vertical Clearance: ADA Standard Section 307.4
Section 307.4 covers the current ADA Standards for vertical clearance.
-
Submerged Depth: ADA Standard Section 1009.3.2
Sloped entries shall extend to a depth of 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level....
-
11B-307.4 Vertical clearance
Vertical clearance shall be 80 inches (2032 mm) high minimum. Guardrails or other barriers shall be provided where the vertical clearance is less than 80 inches (2032 mm) high....
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
11B-307.4 Vertical clearance
Vertical clearance shall be 80 inches (2032 mm) high minimum. Guardrails or other barriers shall be provided where the vertical clearance is less than 80 inches (2032 mm) high....
-
The ADA Standards for Accessible Design (the ADA Standards)
The ADA Standards identify what features need to be accessible, set forth the number of those features that need to be made accessible, and then provide the specific measurements, dimensions...
-
Sections 4.8.5 and 4.9.4
An exception permits the distance between the horizontal projections and the bottom of the gripping surface to be reduced by 1/8 inch for each ½ inch of additional handrail perimeter dimension...
-
Water Closet Centerline and Seat Height
Water closets can be located so that this dimension is met on either the left side or the right side of the fixture....
-
611 Washing Machines and Clothes Dryers
This dimension stems from specifications for obstructed side reaches (308.3)....
