Walks, halls corridors, passageways, aisles, or other circulation spaces shall have 80 in (2030 mm) minimum clear head room (see Fig. 8(a))....
Search Results "Minimum Dimension"
-
Circulation Paths
-
Hager Companies Door Protection Plate 214S
- Plastic Laminate NFPA Notes: - Self-adhesive tape available on all plates - Spanner head screws - Torx head screws - Other colors are available and will be subject to minimum...
-
11B-705.1.2.3 Islands or cut-through medians
Detectable warnings at pedestrian islands or cut-through medians shall be 36 inches (914 mm) minimum in depth extending the full width of the pedestrian path or cut-through less 2 inches...
-
11B-705.1.2.3 Islands or cut-through medians
Detectable warnings at pedestrian islands or cut-through medians shall be 36 inches (914 mm) minimum in depth extending the full width of the pedestrian path or cut-through less 2 inches...
-
Dome Spacing: ADA Standard Section 705.1.2
Truncated domes in a detectable warning surface shall have a center-to-center spacing of 1.6 inches (41 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch...
-
11B-406.5.9 Clear space at diagonal curb ramps
The bottom of diagonal curb ramps shall have a clear space 48 inches (1219 mm) minimum outside active traffic lanes of the roadway....
-
11B-406.5.9 Clear space at diagonal curb ramps
The bottom of diagonal curb ramps shall have a clear space 48 inches (1219 mm) minimum outside active traffic lanes of the roadway....
-
Dome Size: ADA Standard Section 705.1.1
Truncated domes in a detectable warning surface shall have a base diameter of 0.9 inch (23 mm) minimum and 1.4 inches (36 mm) maximum, a top diameter of 50 percent of the base diameter minimum...
-
11B-604.8.2.2 Doors
Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 44 inches (1118 mm) minimum...
-
11B-604.8.2.2 Doors
Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 44 inches (1118 mm) minimum...
-
Diagonal Curb Ramps: ADA Standard Section 406.6
Section 406.6 covers the current ADA Standards for diagonal curb ramps.
-
Grab Bars: ADA Standard Section 1009.4.5
The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls....
-
Allegion LCN 5030 Series Overhead Concealed Door Control
LCN 5030 Series The concealed 5030 Series PACER® is a heavy duty closer designed to fit in a narrow, minimum 1 3/4” aluminum transom....
-
SignOnVRI Video Remote Interpreting
SignOnVRI benefits Highly Skilled ASL interpreters Available to remote areas and for short assignments Save two-hour minimum and travel costs Affordable and reliable Video...
-
Seating Locations
These dimensions allow people using mobility devices (e.g., wheelchairs, scooters, walkers, canes, and crutches) to independently enter and exit the room and move throughout the space, sit...
-
5.4.4.1 Transfer Support Distance from Transfer Surface Recommendation for Stretchers
The Committee proposes that this horizontal dimension be included for stretchers under the proposed rule....
-
A4.23.3 Clear Floor Space
The specific shower shown is designed to fit exactly within the dimensions of a standard bathtub....
-
A4.30.4 Raised and Brailled Characters and Pictorial Symbol Signs (Pictograms)
The standard dimensions for literary Braille are as follows: Dot diameter .059 in. Inter-dot spacing .090 in....
-
Clear Floor Space [4.20.2]
Clear Floor Space [4.20.2] Clear floor space at tubs, which is dimensioned according to the approach, may overlap required turning space within the room....
-
4.1.6(4)(a)
Table 2 -- Allowable Ramp Dimensions for Construction in Existing Sites, Buildings, and Facilities Slope* Maximum Rise Maximum Run Steeper than 1...
-
Self Contained, Closed Products - Side Reach Range
Requires the Accessibility Specialist plan or above. (Login or upgrade your account!)
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-411.2.1.2.3 Accessibility function button
The International Symbol of Accessibility shall comply with Section 11B-703.7.2.1, and shall be 5/8 inch (15.9 mm) minimum in height. The indication shall be three raised dots....
