Reinforcement for grabs bars shall comply with the following: Continuous reinforcement shall be installed in the walls of showers 30 inches (762 mm) maximum to 38 inches (965 mm) minimum...
Search Results "Minimum Dimension"
Filters
Commonly Searched Documents
-
11B-809.10.6.4 Reinforcement for grab bars
-
11B-809.10.8.1 Location
Lavatories without base cabinets shall be installed with the centerline 18 inches (457 mm) minimum from an adjoining wall or fixture to allow for forward approach....
-
8.5 Updating Standards in the Future
As noted above, the general population is increasingly overweight and obese; if population heights and weights change significantly, this might alter dimensions required for equipment accessibility...
-
§382.67(a)
stowage of cargo in the cabin compartment) in the cabin of sufficient size to stow at least one typical adult-sized folding, collapsible, or break-down manual passenger wheelchair, the dimensions...
-
HOW TO MEASURE TRANSFER HEIGHTS IS IMPORTANT
Because of these complex shapes, it is necessary to create a standard method by which to measure table seat dimensions....
-
References:
“Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment.” Memorandum. April 23, 2013....
-
11B-219.3 Receivers
The minimum number of receivers to be provided shall be equal to 4 percent of the total number of seats, but in no case less than two....
-
Clarification on Standard Roll-In Shower Compliance
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
Toe Clearance: ADA Standard Section 604.8.1.4
Section 604.8.1.4 covers the current ADA Standards for toe clearance at wheelchair accessible compartments.
-
Dispensers: ADA Standard Section 604.7
Section 604.7 covers the current ADA Standards for toilet paper dispensers.
-
11B-411.2.2.1 Visible identification
The identification fixture shall be 80 inches (2032 mm) minimum above the finish floor or ground to the bottom of the fixture....
-
Allegion LCN 5030 Series Overhead Concealed Door Control
LCN 5030 Series The concealed 5030 Series PACER® is a heavy duty closer designed to fit in a narrow, minimum 1 3/4” aluminum transom....
-
SignOnVRI Video Remote Interpreting
SignOnVRI benefits Highly Skilled ASL interpreters Available to remote areas and for short assignments Save two-hour minimum and travel costs Affordable and reliable Video...
-
5.2.1.1 Transfer Surface Width Recommendations for M301
5.2.1.1 Transfer Surface Width Recommendations for M301 The Committee recommends a transfer surface of 28 inches minimum width for equipment used by patients in a supine, side-lying,...
-
Doors: ADA Standard Section 604.8.2.2
Section 604.8.2.2 covers the current ADA Standards for ambulatory accessible compartment doors.
-
11B-407.2.2.2 Visible signals
Visible signal fixtures shall be centered at 72 inches (1829 mm) minimum above the finish floor or ground....
-
4.3.5.4 360-degree Turn
Dimensions for 360-degree turning spaces are used to determine the minimum spaces needed for turning around in spaces with only one point of entry....
-
Vertical Clearance: ADA Standard Section 307.4
Section 307.4 covers the current ADA Standards for vertical clearance.
-
Submerged Depth: ADA Standard Section 1009.3.2
Sloped entries shall extend to a depth of 24 inches (610 mm) minimum and 30 inches (760 mm) maximum below the stationary water level....
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
11B-307.4 Vertical clearance
Vertical clearance shall be 80 inches (2032 mm) high minimum. Guardrails or other barriers shall be provided where the vertical clearance is less than 80 inches (2032 mm) high....
-
Size: ADA Standard Section 407.4.8.1.1
Section 407.4.8.1.1 covers the current ADA Standards for size of visible elevator car position indicators.
-
11B-407.4.8.1.1 Size
Characters shall be ½ inch (12.7 mm) high minimum....
-
1.3.2 Focus Following NPRM Comments
Permitted obstructions to the transfer surface Transfer support location and configuration Depth of wheelchair spaces The Advisory Committee, during its deliberations, added dimensions...
