Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door side of the compartment and any obstruction shall be 44 inches (1118 mm) minimum...
Search Results "Minimum Dimension"
-
11B-604.8.2.2 Doors
-
Diagonal Curb Ramps: ADA Standard Section 406.6
Section 406.6 covers the current ADA Standards for diagonal curb ramps.
-
Grab Bars: ADA Standard Section 1009.4.5
The top of the gripping surface shall be 4 inches (100 mm) minimum and 6 inches (150 mm) maximum above transfer walls....
-
Hager Companies Door Protection Plate 214S
- Plastic Laminate NFPA Notes: - Self-adhesive tape available on all plates - Spanner head screws - Torx head screws - Other colors are available and will be subject to minimum...
-
Seating Locations
These dimensions allow people using mobility devices (e.g., wheelchairs, scooters, walkers, canes, and crutches) to independently enter and exit the room and move throughout the space, sit...
-
5.4.4.1 Transfer Support Distance from Transfer Surface Recommendation for Stretchers
The Committee proposes that this horizontal dimension be included for stretchers under the proposed rule....
-
A4.23.3 Clear Floor Space
The specific shower shown is designed to fit exactly within the dimensions of a standard bathtub....
-
A4.30.4 Raised and Brailled Characters and Pictorial Symbol Signs (Pictograms)
The standard dimensions for literary Braille are as follows: Dot diameter .059 in. Inter-dot spacing .090 in....
-
Clear Floor Space [4.20.2]
Clear Floor Space [4.20.2] Clear floor space at tubs, which is dimensioned according to the approach, may overlap required turning space within the room....
-
4.1.6(4)(a)
Table 2 -- Allowable Ramp Dimensions for Construction in Existing Sites, Buildings, and Facilities Slope* Maximum Rise Maximum Run Steeper than 1...
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-411.2.1.2.3 Accessibility function button
The International Symbol of Accessibility shall comply with Section 11B-703.7.2.1, and shall be 5/8 inch (15.9 mm) minimum in height. The indication shall be three raised dots....
-
11B-1009.4.5 Grab bars
The top of the gripping surface shall be 4 inches (102 mm) minimum and 6 inches (152 mm) maximum above transfer walls....
-
11B-1009.4.5 Grab bars
The top of the gripping surface shall be 4 inches (102 mm) minimum and 6 inches (152 mm) maximum above transfer walls....
-
11B-411.2.1.2.3 Accessibility function button
The International Symbol of Accessibility shall comply with Section 11B-703.7.2.1, and shall be 5/8 inch (15.9 mm) minimum in height. The indication shall be three raised dots....
-
Accessible Routes: ADA Standard Section 1007.2
Where accessible routes intersect playing surfaces of holes, a 1 inch (25 mm) maximum curb shall be permitted for a width of 32 inches (815 mm) minimum. 3....
-
11B-809.10.5.2 Reinforcement for grab bars
At the control end wall and head end wall, between 30 inches (762 mm) maximum to 38 inches (965 mm) minimum above the finish floor, extending 28 inches (711 mm) minimum from the front edge...
-
11B-604.2 Location
The centerline of the water closet shall be 17 inches (432 mm) minimum to 18 inches (457 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (432...
-
11B-604.2 Location
The centerline of the water closet shall be 17 inches (432 mm) minimum to 18 inches (457 mm) maximum from the side wall or partition, except that the water closet shall be 17 inches (432...
-
11B-809.10.5.2 Reinforcement for grab bars
At the control end wall and head end wall, between 30 inches (762 mm) maximum to 38 inches (965 mm) minimum above the finish floor, extending 28 inches (711 mm) minimum from the front edge...
-
Allegion LCN 5030 Series Overhead Concealed Door Control
LCN 5030 Series The concealed 5030 Series PACER® is a heavy duty closer designed to fit in a narrow, minimum 1 3/4” aluminum transom....
-
SignOnVRI Video Remote Interpreting
SignOnVRI benefits Highly Skilled ASL interpreters Available to remote areas and for short assignments Save two-hour minimum and travel costs Affordable and reliable Video...
-
Character Height: ADA Standard Section 703.2.5
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
