These types of instruments could be used to measure floor flatness and level but they are very expensive, require training, and give accuracies in excess of what is needed for accessible...
Search Results "Tape Measure"
Filters
Commonly Searched Documents
-
Laser scanners
-
1132A.3, Item 5
A pair of doors, manual or automatic, must have at least one leaf which provides a clear width of not less than 32 inches (813 mm), measured with the door positioned at an angle of 90 degrees...
-
1134A.6, Item 1.3
Other shower stall configurations shall measure at least 36 inches deep by 60 inches wide (914 mm by 1524 mm) with an entrance opening of at least 36 inches (914 mm) when a wall is installed...
-
§ 35.130(f)
(f) A public entity may not place a surcharge on a particular individual with a disability or any group of individuals with disabilities to cover the costs of measures, such as the provision...
-
11B-703.5.8 Character spacing
Character spacing shall be measured between the two closest points of adjacent characters, excluding word spaces....
-
Standards
methods for buildings - setting out and measurement - permissible measuring deviations ISO 4464 Tolerances for buildings - Relationship between the different types of deviations...
-
Inclusion Solutions Offset Door Hinge
The hinge measures 2" x 3-1/2" with a decorative, long lasting brass finish. (2" wide to wrap the trim)....
-
Executive Summary
The structural anthropometric measurements required the measurement of the body and devices size at rest....
-
1.Tax Credit for Small Business (Section 44 of the Internal Revenue Code)
with disabilities; providing qualified interpreters or other methods to make communication accessible to people with hearing disabilities; providing qualified readers, taped...
-
Issue 10: Braille (right side up?)
Manufacturers may provide a paper tape label, showing the street name in print and in Braille, on the back side of the sign....
-
Audio Induction Loop
In addition, the loop can also cause hum in electrical devices not shielded from electromagnetic fields, like a nearby cassette tape player....
-
Employees
Once an employee is on the job, his actual performance is the best measure of ability to do the job....
-
§27.11(c)(2)(iii)
with official approval of recipient's management, any policies or practices that do not meet the requirements of this part according to a schedule or sequence that includes milestones or measures...
-
Clear Width [4.8.3]
The minimum dear width for ramps of 36 inches is measured between the leading edge of handrails. A maximum clear width is not specified....
-
Free-standing and Post-mounted Objects
This is based on standard measures for cane sweep. Objects with leading edges at or below 27 inches or above 80 inches can protrude any amount....
-
11B-703.8.7 Character spacing
Spacing shall be measured between the two closest points of adjacent low resolution VMS characters within a message, excluding word spaces....
-
M301.4 Lift Compatibility
Compatibility M01.4.1 Clearance in Base Proposed requirement: The base of the equipment shall provide a clearance 44 inches (1120 mm) wide minimum, 6 inches (150 mm) high minimum measured...
-
A4.5.1 General
While the dynamic coefficient of friction during walking varies in a complex and non-uniform way, the static coefficient of friction, which can be measured in several ways, provides a close...
-
11B-705.1.1.2 Dome spacing
detectable warning surface shall have a center-to-center spacing of 2.3 inches (58 mm) minimum and 2.4 inches (61 mm) maximum, and a base-to-base spacing of 0.65 inch (16.5 mm) minimum, measured...
-
703.3.1 Dimensions and Capitalization
Table 703.3.1 Braille Dimensions Measurement Range Minimum in Inches Maximum in Inches Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm)...
-
§35.130(f) (Section-by-Section Analysis)
Paragraph (f) provides that a public entity may not place a surcharge on a particular individual with a disability, or any group of individuals with disabilities, to cover any costs of measures...
-
1017.5 Tread Obstacles
This section requires obstacles to not exceed 1/2 inch in height measured vertically to the highest point....
-
Energy Consumption During Ambulation
Measurements were recorded for subjects walking on the Straight and Turning Courses....
-
11B-705.1.2.2.2.2 Two entrance/exit points
Where the turning space has two entrance/exit points other than the sloped ramp segments, detectable warnings shall be 36 inches (914 mm) deep at both entrance/ exit points, as measured...
